LogoPGG 3/1PGG 6/1PGG 8/3
  • General notes
  • Intended use
  • Environmental protection
  • Accessories and spare parts
  • Scope of delivery
  • Safety instructions
    • Hazard levels
    • Safety instructions
    • Symbols on the device
    • Warning symbols
  • Device description
  • Installation
  • Initial start-up
    • Fill with oil
  • Initial startup
    • Check the oil level
    • Refuelling
  • Operation
    • Starting the device
    • Starting with the pull cord starter
    • Connecting AC devices
    • Charging vehicle batteries
      • Circuit breaker
      • Disconnect the vehicle battery
    • Switching off the device
  • Transport
  • Storage
    • Storage duration of 1...2 months
    • Storage duration of 2...12 months
    • Storage duration longer than 12 months
  • Care and service
    • Maintenance intervals
      • Each time before use
      • Once after 1 month or 20 operating hours
      • Every 3 months or 50 operating hours
      • Every 6 months or 100 operating hours
      • Annually by the authorised Customer Service department
      • Every 2 years by the authorised Customer Service department
    • Maintenance work
      • Check the air filter
      • Cleaning the air filter
      • Changing oil
      • Cleaning the settling cup
      • Checking and cleaning the spark plug
      • Charging the device battery
  • Troubleshooting guide
    •  

      The engine does not start.

    •  

      The device does not generate any electricity

  • Warranty
  • Technical data
    • PGG 3/1 50 Hz
    • PGG 3/1 60 Hz
    • PGG 6/1
    • PGG 8/3
  • Declaration of Conformity

      PGG 3/1
      PGG 6/1
      PGG 8/3

      59686310 (05/23)

      General notes

      Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.

      Keep both books for future reference or for future owners.

      Intended use

      As delivered, this generator is intended for use at heights of up to 1500 m above sea level. It can be adjusted by an authorised Customer Service department for use at higher elevations.

      If an electricity generator that has been adjusted for use at higher elevations is used below this height then this can result in destruction of the motor through overheating.

      Environmental protection

      The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

      Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

      Notes on the content materials (REACH)

      Current information on content materials can be found at: www.kaercher.de/REACH

      Accessories and spare parts

      Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

      Information on accessories and spare parts can be found at www.kaercher.com.

      Scope of delivery

      Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

      Safety instructions

      Hazard levels

      DANGER

      Indication of an imminent threat of danger that will lead to severe injuries or even death.

      WARNING

      Indication of a potentially dangerous situation that may lead to severe injuries or even death.

      CAUTION

      Indication of a potentially dangerous situation that may lead to minor injuries.

      ATTENTION

      Indication of a potentially dangerous situation that may lead to damage to property.

      Safety instructions

      DANGER

      Risk of injury.

      • The device is not intended for use by persons with restricted physical, sensory or mental abilities or those lacking in experience and / or lacking in knowledge.

      • Children must be supervised to prevent them from playing with the device.

      • Children and minors must not use the device.

      • Keep a safe distance away from the exhaust pipe and do not reach into the exhaust gas jet.

      DANGER

      Danger of explosion.

      • Never operate the device in potentially explosive environments.

      • Observe the corresponding safety instructions when operating the device in hazard zones (e.g. a petrol station).

      • Only fill the fuel specified in the operating instructions.

      • Only refuel with the engine switched off.

      • Do not refuel in confined spaces.

      • Smoking and open flames are prohibited.

      • Ensure that no fuel gets on hot surfaces during refuelling.

      • Close the fuel tank cap after refuelling.

      • Do not operate the device if fuel has been spilt. Move the device to another location and avoid generating sparks.

      • Store fuel only in approved containers.

      • Do not store fuel in the vicinity of open flames or devices having an ignition flame or that generate sparks (e.g. oven, heating boiler or water heater).

      • Do not spray start spray into the air filter.

      DANGER

      Risk of fire.

      • Maintain a minimum distance of 2 m between inflammable objects and the muffler.

      • Do not operate the device in forests, bushy or grassy areas unless the exhaust pipe has been equipped with a spark catcher.

      • Keep grass and other soiling substances away from the cooling fins.

      • Do not operate the device if the fuel system is damaged or leaking. Check the fuel system regularly.

      • Allow the device to cool down before storing in closed rooms.

      Danger of electric shock

      • Do not touch the spark plug or ignition lead when the device is in operation.

      • Do not operate the device in rain, snow or in the vicinity of a sprinkler system. Keep the device dry.

      • Never touch the mains plug and socket with wet hands.

      • Do not start up a device that has wet or icy electrical components.

      • Do not connect the device only to the mains supply of a building.

      • Preferably use devices and extension cables with rubber cables as per IEC 60245-4.

      WARNING

      Health risk

      • Exhaust gases are toxic. Never breathe in the exhaust gases. Never operate the device in confined spaces. Ensure sufficient ventilation and extraction of the exhaust gases.

      • Make sure that no exhaust gases are emitted close to air vents.

      • Avoid repeated or prolonged contact with fuel or engine oil and do not inhale the fuel vapours.

      CAUTION

      Danger of burns

      • Do not touch any hot parts such as the muffler, cylinder or cooling fins.

      Danger of hearing damage

      • Do not operate the device without a muffler. Check the muffler regularly and have a damaged muffler replaced.

      ATTENTION

      Risk of damage

      • Use only spare parts from the original manufacturer.

      • Old fuel can lead to deposits in the carburettor and impair the engine performance. Use only new fuel.

      • Do not adjust any control springs or linkages that might increase the speed of the engine.

      • Do not operate the device with the air filter removed.

      • Do not pull the starter cord while the device is running.

      • Ensure adequate ventilation so that the device does not overheat.

      Symbols on the device

      WARNING

      Danger of explosion, risk of fire.

      Petrol can cause fires or explosions if handled incorrectly.

      Shut the motor down prior to refuelling.

      Do not operate the device in confined spaces or partially enclosed areas.

      Read these operating instructions before using the device.

      ATTENTION

      Risk of damage

      Do not refuel with diesel fuel.

      Note:

      Check the oil level before starting the device. The engine stops and the indicator lamp lights up if the oil level is too low. Refill oil (for oil type see "Technical data").

      WARNING

      Danger of explosion, risk of fire.

      Shut the motor down prior to refuelling.

      Clean up any spilt fuel before starting the device.

      Do not start the device if the fuel system is leaky.

      CAUTION

      Hot surface

      The exhaust pipe of the device becomes very hot during operation and can cause burns.

      Avoid touching the exhaust pipe.

      WARNING

      Risk of eye injuries and hearing damage.

      Wear safety goggles and hearing protection when operating the device.

      Warning symbols

      Observe the following warnings when handling the batteries:

      Observe notes in the instructions for the battery, on the battery and in these operating instructions.
      Wear eye protection.
      Keep acids and batteries away from children.
      Risk of explosion
      Fire, sparks, open flames and smoking are prohibited.
      Risk of acid burns
      First aid.
      Warning
      Disposal
      Do not throw batteries in the bin.

      Device description

      1. Air filter
      2. Push handle
      3. Starter cord
      4. Choke lever
      5. Fuel cock
      6. Fuel tank
      7. Control panel
      8. Battery
      9. Oil dipstick
      10. Oil drain plug
      11. Fuel tank filling level display
      12. Fuel tank cap
      13. Type plate
      14. Indicator lamp
      15. Engine key-operated switch
      16. DC circuit breaker
      17. DC terminals
      18. AC voltmeter
      19. Power circuit breaker
      20. AC power socket
      21. PGG 6/1: AC power socketPGG 8/3: Three-phase socket
      22. Earthing terminal
      Symbols on the device

      Clean the air filter every 50 operating hours or every 10 operating hours in the case of dusty environments(see "Care and maintenance/Cleaning the air filter").

      Note on checking the oil level.

      Choke lever

      Installation

      1. Mount the push handle on the device frame using the mounting materials provided.

        1. Push handle
        2. Stands
        3. Wheel

      2. Mount the wheels on the device frame using the mounting materials provided.

      3. Mount the stands on the device frame using the mounting materials provided.

      Initial start-up

      Fill with oil

      1. Position the device on a level surface.

      2. Unscrew the oil dipstick.

      3. Fill with engine oil.

        Note: The engine oil is not included in the scope of delivery. The filling quantity and oil type are specified in the section "Technical data".

      4. Wipe off the oil dipstick.

      5. Insert the oil dipstick as far as it will go, but do not screw in.

      6. Pull out the oil dipstick. The oil level must lie in the marked section of the oil dipstick.

      7. Top up the engine oil if the level is too low.

      8. Screw in and tighten the oil dipstick.

      Initial startup

      Check the oil level

      1. Position the device on a level surface.

      2. Unscrew the oil dipstick.

      3. Wipe off the oil dipstick.

      4. Insert the oil dipstick as far as it will go, but do not screw in.

      5. Pull out the oil dipstick. The oil level must lie in the marked section of the oil dipstick.

      6. Top up the engine oil if the level is too low.

      7. Screw in and tighten the oil dipstick.

      Refuelling

      1. Read the fuel level indicator.

      2. Refill the fuel tank with the tank indicator shows a low filling level.

      3. Unscrew the fuel tank cap.

      4. Fill fuel up a maximum of the lower edge of the filling nozzle.

      5. Fit the fuel tank cap and screw tight.

      Operation

      Starting the device

      1. Open the fuel cock.

      2. Push the choke lever to the left if the engine is cold.

      3. Turn the key-operated switch to the START position and hold in this position until the engine starts. Hold the key-operated switch in the START position for no longer than 5 seconds. Wait for at least 10 seconds before attempting to start again.

      4. Allow the key-operated switch to return to the 1/ON position when the engine has started.

      5. Push the choke lever to the right once the engine has started.

      Starting with the pull cord starter

      1. Open the fuel cock.

      2. Push the choke lever to the left if the engine is cold.

      3. Pull the starter cord slowly until a strong resistance is discernible then pull strongly.

      4. Slowly return the starter cord.

        ATTENTION

        Risk of damage

        A rapidly returning starter cord damages the device.

        Slowly return the starter cord.

      5. Push the choke lever to the right once the engine has started.

      Connecting AC devices

      The power consumption of the electrical device must not exceed the continuous power rating of the generator. The maximum power may only be used for brief periods. Devices with electric motors require several times the nominal power when starting up.

      DANGER

      Danger of electric shock

      Electricity can flow through the operator and cause death or injuries if the electrical equipment or cables are damaged.

      A fault current protection device (PRCD Portable Residual Current Device) must be connected between each additional device and the generator if more than one device is plugged into the generator.

      1. Start the generator.

      2. Set the power switch to 1/ON.

      3. Plug the mains plug of the electrical device into the socket of the generator.

      4. A fault current protection device (PRCD Portable Residual Current Device) must be connected between each additional device and the generator if more than one device is plugged into the generator.

      5. Start the electrical device.

        If the device does not function correctly, e.g. irregular running or misfires, immediately switch off and unplug the connected appliances and investigate the cause.

      Charging vehicle batteries

      The 12 V DC connection is only suitable for charging 12 V lead-acid automobile batteries. This connection is not suitable for use as a 12 V power supply for electrical appliances.

      1. Disconnect the vehicle minus cable (black) from the battery.

      2. Connect the plus terminal (red) of the charging cable to the plus terminal of the battery.

      3. Connect the plus terminal (red) of the other end of the charging cable to the red terminal (+) of the generator.

      4. Connect the minus terminal (black) of the charging cable to the minus terminal of the battery.

      5. Connect the minus terminal (black) of the other end of the charging cable to the black terminal (-) of the generator.

      6. Start the generator.

        ATTENTION

        Risk of damage.

        The vehicle or generator can be damaged during charging if the vehicle engine is running while charging the vehicle battery.

        Do not start the vehicle while charging the battery.

      Circuit breaker

      The circuit breaker button pops out and interrupts charging if an overload occurs.

      1. Wait a few minutes and then press the button in again.

      Disconnect the vehicle battery

      1. Shut down the generator.

      2. Disconnect the minus pole (black) from the generator.

      3. Disconnect the minus terminal (black) from the battery.

      4. Disconnect the plus pole (red) from the generator.

      5. Disconnect the plus terminal (red) from the battery.

      6. Connect the vehicle minus cable (black) to the minus pole of the battery.

      Switching off the device

      1. Turn the key-operated switch to "0/OFF".

      2. Close the fuel cock.

      Transport

      • Turn the key-operated switch to 0/OFF and close the fuel cock before transport.

      • Push the push handle upwards.

      • Push or pull the device using the push handle.

      • Allow the engine to cool down for at least 15 minutes before loading.

      • Keep the device horizontal during transport to prevent fuel from spilling out.

      • When transporting in vehicles, secure the device against rolling away, slipping and tipping according to the respectively applicable guidelines.

      • Be aware of the weight of the device during transport.

      Storage

      CAUTION

      Failure to observe the weight

      Risk of injury and damage

      Be aware of the weight of the device during storage.

      ATTENTION

      Risk of damage

      Do not place any heavy objects on the device.

      Store the device in a dry and dust-free place.

      Storage duration of 1...2 months

      1. Add petrol stabiliser to the fuel tank.

      2. Top up the fuel tank.

      Storage duration of 2...12 months

      Additionally:

      1. Close the fuel cock.

      2. Place a container under the carburettor.

        1. Carburettor
        2. Drain screw

      3. Unscrew the drain screw.

      4. Collect the fuel in the container.

      5. Screw in and tighten the drain screw.

      6. Empty the settling cup (see "Care and Maintenance/Cleaning the settling cup").

      Storage duration longer than 12 months

      Additionally:

      1. Unscrew the spark plug.

      2. 5...10 cm3 Add engine oil to the cylinder.

      3. Slowly pull the starter cord several times to distribute the oil in the engine.

      4. Screw in the spark plug.

      5. Change the oil (see "Care and Maintenance/Changing the oil").

      6. Pull the starter cord slowly until a strong resistance is discernible.

      Care and service

      DANGER

      Danger of injury from electric shock.

      You can be injured by moving parts. The electrical voltage generated by the device can kill or injure you.

      Remove the spark plug connector and disconnect the battery before performing any maintenance work.

      CAUTION

      Danger of burns.

      Hot device components cause burns if touched.

      Allow the device to cool down before working on it.

      * See "Startup" for a description.

      ** See "Maintenance work" for a description.

      Maintenance intervals

      Each time before use

      1. Check the device for correct condition and operational safety. Do not start up a damaged device.

      2. Check the oil level. *

      3. Check the air filter. **

      Once after 1 month or 20 operating hours

      1. Change the oil. **

      Every 3 months or 50 operating hours

      1. Clean the air filter. **

        Perform cleaning more frequently in a dusty application environment.

      Every 6 months or 100 operating hours

      1. Change the oil. **

      2. Clean the settling cup. **

      3. Check and clean the spark plug. **

      4. Clean the spark catcher (not included in the scope of delivery). **

      Annually by the authorised Customer Service department

      1. Check and adjust the valve play.

      2. Clean the fuel tank and fuel filter.

      Every 2 years by the authorised Customer Service department

      1. Check the fuel line and replace if necessary.

      Maintenance work

      Check the air filter

      1. Pivot the lock away or unscrew the screw.

        1. Screw
        2. Cover
        3. Air filter insert
        4. Lock

      2. Remove the cover.

      3. Check the air filter insert for soiling. Clean the air filter if necessary or replace if damaged (see "Cleaning the air filter").

      4. Fit the cover.

      5. Close the lock or screw in and tighten the screw.

      Cleaning the air filter

      ATTENTION

      Risk of damage

      Penetrating dust can destroy the engine if the air filter insert is absent.

      Do not operate the device without an air filter insert.

      1. Open the air filter (see "Checking the air filter").

      2. Remove the air filter insert.

      3. Wash the air filter insert in warm water and household cleaner then rinse with clear water.

        Note: Dispose of the oil contaminated washing solution in an environmentally friendly manner.

      4. Allow the air filter insert to dry.

      5. Saturate the air filter insert in clean engine oil and press out the excess oil.

      6. Fit the air filter insert back into place.

      7. Fit the cover.

      8. Close the latches.

      Changing oil

      Perform the oil change on a warm engine.

      1. Unscrew the oil dipstick.

        1. Oil dipstick
        2. Oil drain plug

      2. Unscrew the oil drain screw with seal and catch the escaping oil.

      3. Screw in and tighten the oil drain screw with seal.

      4. Position the device on a level surface.

      5. Measure the correct quantity of engine oil (for oil type see "Technical data") and fill through the oil dipstick hole.

      6. Check the oil level (see "Starting up").

      7. Screw in and tighten the oil dipstick.

      8. Dispose of the old oil in accordance with the environmental regulations.

      Cleaning the settling cup

      The settling cup separates water from the petrol.

      1. Close the fuel cock.

      2. Unscrew the settling cup.

        1. Settling cup
        2. Screw

      3. Remove the settling cup with O-ring.

      4. Clean the settling cup and O-ring using a non-inflammable solvent and allow to dry.

      5. Fit the settling cup and O-ring and screw tight.

      6. Open the fuel cock.

      7. Check the seal between the settling cup and carburettor.

      8. Close the fuel cock.

      Checking and cleaning the spark plug

      1. Pull off the spark plug connector.

        1. Spark plug connector
        2. Spark plug

      2. Clean the region around the spark plug to prevent dirt from entering the engine when the spark plug is removed.

      3. Unscrew the spark plug.

      4. Replace a spark plug that has worn electrodes or a broken insulator.

      5. Check the electrode gap of the spark plug. Target value 0.7...0.8 mm.

      6. Check the spark plug seal for damage.

        ATTENTION

        Risk of damage

        A loose spark plug can overheat and damage the engine. An overtightened spark plug can damage the thread in the engine.

        Observe the following instructions for tightening the spark plug.

      7. Carefully screw the spark plug in by hand. Do not cross the thread.

      8. Screw the spark plug all the way in using the plug spanner and the tighten as follows.

        1. Tighten a used spark plug by an additional 1/8...1/4 turn.

        2. Tighten a new spark plug by an additional 1/2 turn.

      9. Plug on the spark plug connector.

      Charging the device battery

      DANGER

      Danger of explosion, risk of fire

      Danger of injury

      Connecting the two battery terminals causes a short-circuit that can result in an explosion or fire.

      Never place a metal object (e.g. a tool) on the battery.

      Observe the safety instructions on the handling of batteries.

      Observe the operating instructions for the charger.

      CAUTION

      Health risk

      Lead is harmful to your health.

      Never allow lead to come into contact with open wounds.

      1. Check the battery acid level.

      2. If the battery acid level is too low:

        1. Remove the cell cap.

        2. Top up the cell with distilled water up to the marking.

        3. Fit the cell cap.

      3. Disconnect the battery.

      4. Connect the plus cable of the charger to the plus terminal of the battery.

      5. Connect the minus cable of the charger to the minus terminal of the battery.

      6. Switch on the charger.

      Troubleshooting guide

      Have all checks and work on electrical parts performed by an expert.

      In case of any malfunctions not mentioned in this chapter, contact the authorised Customer Service.

      • The engine does not start. 

      • The device does not generate any electricity 

       

      The engine does not start.

      Remedy:

      1. Open the fuel cock.

      2. Fill the tank with fuel.

      3. Check the oil level and top up if necessary.

      4. Check the spark plug (see"Care and maintenance/Checking and cleaning the spark plug").

      5. Clean the settling cup (see "Care and Maintenance/Cleaning the settling cup").

       

      The device does not generate any electricity

      Remedy:

      1. Set the power switch to 1/ON.

      Warranty

      The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

      You can find more detailed information at: www.kaercher.com/dealersearch

      Technical data

      • PGG 3/1 50 Hz 

      • PGG 3/1 60 Hz 

      • PGG 6/1 

      • PGG 8/3 

      PGG 3/1 50 Hz

      Generator
      Continuous output
      2,8 kW
      Maximum short-term output
      3,0 kW
      cos φ
      1
      Mains voltage
      230 (2x) V
      Phase
      1 ~
      Frequency
      50 Hz
      Degree of protection
      IP23M
      Insulation class
      B
      Design class
      G1
      DC output
      Voltage
      12 V
      current
      6 A
      Internal combustion engine
      Engine type
      Einzylinder
      Type
      4-takt
      Cooling type
      luftgekühlt
      Engine capacity
      208 cm3
      Engine performance
      4,0/5,4 kW/PS
      Fuel type
      Benzin, min. 86 Oktan
      Fuel tank capacity
      15
      Working time with full tank, 100% performance
      6,5 h
      Working time with full tank, 50% performance
      12 h
      Engine oil volume
      0,6 l
      Oil type
      10 W-30 15 W-40
      Spark plug type
      F5T, F6T, F7TJC
      Battery
      Working voltage of the battery
      12 V
      Dimensions and weights
      Length
      645 mm
      Width
      622 mm
      Height
      559 mm
      Weight without fuel
      52 kg
      Determined values in acc. with EN 60335-2-79
      Sound pressure level LpA
      74 dB(A)
      Uncertainty KpA
      1 dB(A)
      Sound power level LWA + uncertainty KWA
      94 dB(A)
      CO2Emissions according to the measurement procedure of EU regulation 2016/1628 Euro V
      Motor
      790 g/kWh

      PGG 3/1 60 Hz

      Generator
      Continuous output
      2,8 kW
      Maximum short-term output
      3,0 kW
      cos φ
      1
      Mains voltage
      220 (2x) V
      Phase
      1 ~
      Frequency
      60 Hz
      Degree of protection
      IP23M
      Insulation class
      B
      Design class
      G1
      DC output
      Voltage
      12 V
      current
      6 A
      Internal combustion engine
      Engine type
      Einzylinder
      Type
      4-takt
      Cooling type
      luftgekühlt
      Engine capacity
      208 cm3
      Engine performance
      4,0/5,4 kW/PS
      Fuel type
      Benzin, min. 86 Oktan
      Fuel tank capacity
      15
      Working time with full tank, 100% performance
      6,5 h
      Working time with full tank, 50% performance
      12 h
      Engine oil volume
      0,6 l
      Oil type
      10 W-30 15 W-40
      Spark plug type
      F5T, F6T, F7TJC
      Battery
      Working voltage of the battery
      12 V
      Dimensions and weights
      Length
      645 mm
      Width
      622 mm
      Height
      559 mm
      Weight without fuel
      52 kg
      Determined values in acc. with EN 60335-2-79
      Sound pressure level LpA
      74 dB(A)
      Uncertainty KpA
      1 dB(A)
      Sound power level LWA + uncertainty KWA
      94 dB(A)

      PGG 6/1

      Generator
      Continuous output
      5,0 kW
      Maximum short-term output
      5,5 kW
      cos φ
      1
      Mains voltage
      230 (3x) V
      Phase
      1 ~
      Frequency
      50 Hz
      Degree of protection
      IP23M
      Insulation class
      B
      Design class
      G1
      DC output
      Voltage
      12 V
      current
      6 A
      Internal combustion engine
      Engine type
      Einzylinder
      Type
      4-takt
      Cooling type
      luftgekühlt
      Engine capacity
      389 cm3
      Engine performance
      8,5/11,6 kW/PS
      Fuel type
      Benzin, min. 86 Oktan
      Fuel tank capacity
      25
      Working time with full tank, 100% performance
      6,5 h
      Working time with full tank, 50% performance
      10 h
      Engine oil volume
      1,1 l
      Oil type
      10 W-30 15 W-40
      Spark plug type
      F5T, F6T, F7TJC
      Battery
      Working voltage of the battery
      12 V
      Dimensions and weights
      Length
      743 mm
      Width
      713 mm
      Height
      670 mm
      Weight without fuel
      85 kg
      Determined values in acc. with EN 60335-2-79
      Sound pressure level LpA
      75 dB(A)
      Uncertainty KpA
      1 dB(A)
      Sound power level LWA + uncertainty KWA
      95 dB(A)
      CO2Emissions according to the measurement procedure of EU regulation 2016/1628 Euro V
      Motor
      678 g/kWh

      PGG 8/3

      Generator
      Continuous output
      7,0 kW
      Maximum short-term output
      7,5 kW
      cos φ
      1
      Mains voltage
      230 (2x), 400 (1x) V
      Phase
      1 / 3 ~
      Frequency
      50 Hz
      Degree of protection
      IP23M
      Insulation class
      B
      Design class
      G1
      DC output
      Voltage
      12 V
      current
      6 A
      Internal combustion engine
      Engine type
      Einzylinder
      Type
      4-takt
      Cooling type
      luftgekühlt
      Engine capacity
      439 cm3
      Engine performance
      9,0/12,2 kW/PS
      Fuel type
      Benzin, min. 86 Oktan
      Fuel tank capacity
      25
      Working time with full tank, 100% performance
      5,5 h
      Working time with full tank, 50% performance
      7 h
      Engine oil volume
      1,1 l
      Oil type
      10 W-30 15 W-40
      Spark plug type
      F5T, F6T, F7TJC
      Battery
      Working voltage of the battery
      12 V
      Dimensions and weights
      Length
      743 mm
      Width
      713 mm
      Height
      670 mm
      Weight without fuel
      90 kg
      Determined values in acc. with EN 60335-2-79
      Sound pressure level LpA
      76 dB(A)
      Uncertainty KpA
      1 dB(A)
      Sound power level LWA + uncertainty KWA
      96 dB(A)
      CO2Emissions according to the measurement procedure of EU regulation 2016/1628 Euro V
      Motor
      678 g/kWh

      Declaration of Conformity

      EU Declaration of Conformity

      We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

      Product: Power generator

      Type: 1.042-xxx

      Currently applicable EU Directives

      2006/42/EC (+2009/127/EC)

      2011/65/EU

      2014/30/EU

      2000/14/EC

      Harmonised standards used

      EN ISO 8528-13: 2016

      EN 60204-1:2018

      EN 55012: 2007 + A1: 2009

      EN 61000-6-1: 2019

      EN IEC 63000: 2018

      EN 62233: 2008

      Applied conformity evaluation method

      2000/14/EG: Annex V

      Sound power level dB(A)

      PGG 3/1

      Measured:

      Guaranteed: 96

      PGG 6/1

      Measured:

      Guaranteed: 97

      PGG 8/3

      Measured:

      Guaranteed: 97

      The signatories act on behalf of and with the authority of the company management.

      Documentation supervisor:

      S. Reiser

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Ph.: +49 7195 14-0

      Fax: +49 7195 14-2212

      Winnenden, 2023/05/01

      Declaration of Conformity (UK)

      We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

      Product: Power generator

      Type: 1.042-xxx

      Currently applicable UK Regulations

      S.I. 2008/1597 (as amended)

      S.I. 2012/3032 (as amended)

      S.I. 2016/1091 (as amended)

      S.I. 2001/1701 (as amended)

      Designated standards used

      EN ISO 8528-13: 2016

      EN 60204-1:2018

      EN 55012: 2007 + A1: 2009

      EN 61000-6-1: 2019

      EN IEC 63000: 2018

      EN 62233: 2008

      Applied conformity assessment procedure

      S.I. 2001/1701 (as amended): Schedule 8

      Sound power level dB(A)

      PGG 3/1

      Measured:

      Guaranteed: 96

      PGG 6/1

      Measured:

      Guaranteed: 97

      PGG 8/3

      Measured:

      Guaranteed: 97

      The signatories act on behalf of and with the authority of the company management.

      Documentation supervisor:

      S. Reiser

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Ph.: +49 7195 14-0

      Fax: +49 7195 14-2212

      Winnenden, 2023/05/01

      <BackPage>

       



      </BackPage>