Read this safety chapter and these original operating instructions before using the device for the first time. Act in accordance with them. Keep the original operating instructions for future reference or for future owners.

The term "power tool" in the warnings refers to your mains-operated (corded) product or battery-operated (cordless) product.

1. Work area safety

   1. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

   2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

   3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2. Electrical safety

   1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.

   2. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

   3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

   4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

   5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

   6. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

   1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

   2. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

   3. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

   4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

   5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

   6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

   7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

   8. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury with a fraction of a second.

4. Power tool use and care

   1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

   2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

   3. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

   4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

   5. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

   6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

   7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

   8. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Battery tool use and care

   1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

   2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

   3. When battery pack is not in use, keep it away from other metal objects, like paperclips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

   4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

   5. Do not use a battery pack or tool that is damaged or modified. Damaged of modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

   6. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.

   7. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

6. Service

   1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

   2. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

a) Do not use the hedge trimmer in bad weather conditions, especially when there is a risk of lightning.This decreases the risk of being struck by lightning.

b) Keep all power cords and cables away from cutting area. Power cords or cables may be hidden in hedges or bushes and can be accidentally cut by the blade.

c) Wear ear protection. Adequate protective equipment will reduce the risk of hearing loss.

d) Hold the hedge trimmer by insulated gripping surfaces only, because the blade may contact hidden wiring. Blades contacting a “live” wire may make exposed metal parts of the hedge trimmer “live” and could give the operator an electric shock.

e) Keep all parts of the body away from the blade. Do not remove cut material or hold material to be cut when blades are moving. Blades continue to move after the switch is turned off. A moment of inattention while operating the hedge trimmer may result in serious personal injury.

f) When clearing jammed material or servicing the hedge trimmer, make sure all power switches are off and the battery pack is removed or disconnected. Unexpected actuation of the hedge trimmer while clearing jammed material or servicing may result in serious personal injury.

g) Carry the hedge trimmer by the handle with the blade stopped and taking care not to operate any power switch. Proper carrying of the hedge trimmer will decrease the risk of inadvertent starting and resultant personal injury from the blades.

h) When transporting or storing the hedge trimmer, always use the blade cover. Proper handling of the hedge trimmer will decrease the risk of personal injury from the blades.

To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse the tool, battery back, or charger in fluid or allow fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.

• Charge the battery pack in a location where the ambient temperature is between 10°C and 38°C.

• Store the battery pack in a location where the ambient temperature is between 0°C and 40°C.

• Use the battery pack in a location where the ambient temperature is between 0°C and 40°C.

• The battery-powered grass and shrub shears are only intended for private use.

• The battery-powered grass and shrub shears are designed for working outdoors in a well-ventilated area.

• In applications with the shearing attachment, the device is used for easy grass trimming.

• In applications with the shrub blade, the device is used for easy bush, hedge and shrub trimming.

Any other use is prohibited.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

---

The blade guard is an important component of the safety devices for the grass shears and shrub blade. A damaged blade guard must not be used and must be replaced immediately.

The unlocking button blocks the power switch, and thus prevents an uncontrolled start-up of the device.

---

1. Trigger lockout button
2. Trigger

To start up the device, first press the unlocking button and then the Trigger.

The maximum amount of equipment is described in these operating instructions. Depending on the model used, there are differences in the scope of delivery (see packaging).

---

1. Shrub blade blade guard
2. Shrub blade cutting blade
3. Grass shears blade guard
4. Grass shears cutting blade
5. Trigger lockout button
6. Handle
7. Battery pack unlocking button
8. Trigger
9. Cutting blade mounting button
10. Cutting blade mount
11. *Charger
12. *Rechargeable battery pack

* optional

The device can be operated with a 18V Kärcher Battery Power battery pack.

---

1. Install the cutting blade.

   1. Undo the cutting blade mounting button.

   2. Take off the cutting blade mounting button.

   3. Put the cutting blade of the grass or shrub shears onto the cutting blade mount.

   4. Put on the cutting blade mounting button.

   5. Tighten the cutting blade mounting button.

---

1. Slide the blade guard over the blade.

1. Push the battery pack into the mounting on the device.

   ---

   

1. Remove the blade guard.

2. Switch the device on.

   ---

   

   1. Pull the trigger lockout button backward to the end.

   2. Press the trigger.

   The device starts up.

3. Guide the cutting blade parallel to the ground.

   ---

   

1. Switch the device on.

   ---

   

   1. Pull the trigger lockout button backward to the end.

   2. Press the trigger.

   The device starts up.

2. Guide the cutting blade parallel to the hedge.

   ---

   

1. Remove the battery pack, see Chapter Removing the battery pack.

2. Slide the blade guard over the cutting blade.

   ---

   

3. Change the cutting blade.

   ---

   

   1. Release the mounting button from the cutting blade.

   2. Remove the mounting button.

   3. Remove the cutting blade of the grass or shrub shears.

   4. Fit the cutting blade of the grass or shrub shears onto the mount.

   5. Place the mounting button onto the cutting blade.

   6. Refit the mounting button on the cutting blade.

1. Pull the unlocking button towards the battery pack.

2. Press the unlocking button inward to unlock the battery pack.

3. Remove the battery pack from device.

   ---

   

1. Remove the battery pack from the device (see Chapter Removing the battery pack).

2. Clean the device (see Chapter Cleaning the device).

1. Remove the battery pack, see Chapter Removing the battery pack.

2. Slide the blade guard over the cutting blade.

   ---

   

3. Removing the cutting blade.

   ---

   

   1. Release the mounting button from the cutting blade.

   2. Remove the mounting button from the cutting blade.

   3. Removing the cutting blade.

   4. Place the mounting button onto the cutting blade.

   5. Refit the mounting button on the cutting blade.

4. Secure the device against slipping and tipping over when transporting in vehicles.

1. To clean the device, see ChapterCleaning the device.

2. Install the blade guard.

   ---

   

3. Store the device in a dry, well ventilated location. Keep away from corrosive substances such as garden chemicals and defrosting salt. Do not store the device outdoors.

---

1. Remove residual mown material from the cutting blade using a hand brush.

2. Clean the unit parts with a damp cloth if required.

3. Regularly remove dirt and foreign objects from the battery mount and electrical contacts.

4. Install the blade guard.

In order to maintain the blade quality, the blade sections should be oiled after each use.

---

1. Place the device on a flat surface.

2. Apply oil to the top of the blade sections.

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

As the battery pack ages, even if it is looked after, its capacity reduces such that the full run time will no longer be reached when fully charged. This does not indicate a defect.

• The device does not start up 

• The device does not start up 

• The device does not start up 

• The device stops during operation 

• The device stops during operation 

Cause:

Battery pack is not inserted correctly.

Remedy:

• Push the battery pack into the mounting until it latches into place.

Cause:

Battery pack is empty

Remedy:

• Charge the battery pack.

Cause:

Battery pack is defective.

Remedy:

• Replace the battery pack.

Cause:

Motor has overheated

Remedy:

• Stop working and allow the motor to cool down.

Cause:

The battery has overheated

Remedy:

• Stop working and allow the battery to cool down to normal battery temperature.

The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

You can find more detailed information at: www.kaercher.com/dealersearch

The declared vibration total values and the declared noise emission values have been measured in accordance with a standard test method and may be used for comparing one tool with another.

The declared vibration total values and the declared noise emission values may also be used in a preliminary assessment of exposure.

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

Product: Battery-operated grass and shrub shears

Type: GSH 18-20 Battery

2006/42/EC (+2009/127/EC)

2014/30/EU

2000/14/EC (+2005/88/EC)

2011/65/EU

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 1997+A1: 2001+A2: 2008

EN 62841-1: 2015 + A11: 2022

EN 62841-4-2:2019+A1:2022+A11:2022

EN IEC 62841-4-5:2021+A11:2021

EN IEC 63000-3:2018

2000/14/EC and amended by 2005/88/EC: Annex V (with shrub blade only)

Measured:86,1

Guaranteed:89

The signatories act on behalf of and with the authority of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2023/02/01

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

Product: Battery-operated grass and shrub shears

Type: GSH 18-20 Battery

S.I. 2008/1597 (as amended)

S.I. 2016/1091 (as amended)

S.I. 2001/1701 (as amended)

S.I. 2012/3032 (as amended)

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 1997+A1: 2001+A2: 2008

EN 62841-1: 2015 + A11: 2022

EN 62841-4-2:2019+A1:2022+A11:2022

EN IEC 62841-4-5:2021+A11:2021

EN IEC 63000-3:2018

S.I. 2001/1701 (as amended): Schedule 8 (with shrub blade only)

Measured: 86,1

Guaranteed: 89

The undersigned act on behalf and under the power of attorney of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2023/02/01