Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.

Keep both books for future reference or for future owners.

Only use the device in private households.

In accordance with the descriptions and the safety information in these operating instructions, the device is intended for use as a wet and dry vacuum cleaner.

Cold ashes may only be vacuumed with suitable accessories.

Protect the device from rain and do not store it outdoors.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.com/REACH

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

(See overleaf for the address)

Depending on the model selected, there are differences in the equipment. The specific equipment is described on the device packaging.

---

1. Suction hose connection
2. Turn switch
3. Parking position handle / accessory holder
4. Foldable carrying handle
5. Storage area
6. Type plate with technical data (e.g. container size)
7. Blowing function
8. Container closure
9. Mains connection cable with mains plug
10. Accessory mounting
11. Parking position for floor nozzle
12. Steering roller
13. Device socket
14. Hose storage, both sides (WD 3 / KWD 3)
15. Cable clips (WD 3 / KWD 3)
16. Filter bag
17. Foam filter
18. Cartridge filter
19. Suction hose (WD 2 Plus / KWD 2)
20. Removable handle (WD 3 / KWD 3)
21. Suction hose with connection piece (WD 3 / KWD 3)
22. Suction pipes 2 x 0.5 m
23. Crevice nozzle
24. ** Floor nozzle with insert for wet and dry vacuuming
25. Adapter for connecting power tools
26. Switchable floor nozzle for carpets and hard floors (home)
27. Upholstery nozzle (home)
28. 2x filter bags (home)
29. Car nozzle (car)
30. Extra long crevice nozzle (car)
31. Suction brush with hard bristles (car)
32. Suction brush with soft bristles (car / workshop)
33. Flexible tool hose (workshop)

** Not included with the home version

1. Before initial startup, remove contents from the container.

   ---

   

   ---

   

   Note

   For devices with stainless steel containers, the accessories are not in the container, they are outside of it.

1. Fully unfold the filter bag.

2. Attach the filter bag to the device connection and press it on firmly.

   ---

   

3. Fit and lock the device head.

   ---

   

1. Connect the suction hose.

   ---

   

2. Connect the suction hose to the handle.

   ---

   

   Note

   For convenient vacuuming in confined spaces, the handle can be removed, and the accessories plugged directly onto the suction hose.

   To release the handle, the grey areas on both sides of the handle must be pressed, and the handle pulled from the hose.

3. Install the floor nozzle.

   • Install the insert in the floor nozzle.

   • Connect the floor nozzle to the suction pipes.

   ---

   

1. Plug the mains plug into the socket.

   ---

   

Devices without a socket

2. Set the trigger into the desired position.

   ---

   

   • Position "1 ON": The suction / blower function is activated.

   • Position "0 OFF": The device is switched off.

Devices with a socket

3. Set the trigger into the desired position.

   ---

   

   • Position "1 ON": The suction / blower function is activated.

   • Position : When the power tool is connected, the suction is activated automatically.

   • Position "0 OFF": The device is switched off.

     Note

     As long as the device is supplied with power, the device socket can be used as a power source.

     Note

     Limited for Switzerland only: The socket outlet shall only be used during operation in dry condition.

Depending on the equipment variant, a foam filter or a cartridge filter is included.

• For devices with a foam filter: Always use the filter bag in addition to the foam filter when dry vacuuming.

• For devices with a cartridge filter: Always use the filter bag in addition to the cartridge filter when vacuuming fine dust.

  Note

  Replace the filter bag in good time, as a filter bag that is too full could be damaged. The fill degree of the filter bag depends on the amount of dirt vacuumed. The filter bag should be replaced more frequently when vacuuming fine dust, sand, etc.

1. Connect the suction hose.

   ---

   

2. If necessary, the adapter can be adjusted to the connection diameter of the power tool with a suitable tool.

3. Option A) Put the adapter on the handle of the suction hose. Connect the suction hose to the adapter on the power tool.

   Option B) For more flexibility when working, connect the adapter to the thin tool hose and the handle of the suction hose and connect it to the power tool.

   Option C) With some power tools, the handle of the suction hose can be connected directly to the power tool.

   ---

   

4. Plug the mains plug of the power tool into the device socket.

   ---

   

5. Set the trigger to MAX Set.

   The power can be regulated using the rotary switch.

   The suction is activated automatically.

   ---

   

The blower function can be used to clean areas that are difficult to reach or where vacuuming is not possible, e.g. leaves in a gravel bed.

• Insert the suction hose into the blower connection. The blower function is now activated.

  ---

  

1. Set the trigger to "0 OFF".

   The device is switched off.

2. Variant 1: Place the handle of the suction hose in the intermediate parking position.

   ---

   

   Variant 2: Attach the floor nozzle in the parking position.

   ---

   

1. Set the trigger to "0 OFF".

   The device is switched off.

2. Pull out the mains plug.

3. Remove the device head.

   ---

   

4. Empty the container.

   ---

   

5. Storage possibility:

   ---

   

   Note

   The suction hose can be wrapped around the device head and attached to the device head with the help of the hose collar.

6. Store the device in a dry and frost-proof room.

• Connect the floor nozzle to the suction pipes.

  ---

  

• Connect the various nozzles, such as the crevice nozzle, to the handle or attach it directly to the suction hose.

• For vacuuming carpet, use the position with brush strips retracted on the bottom.

• For vacuuming hard floors, use the position with the brush strips extended on the bottom.

  ---

  

• For vacuuming upholstered furniture, mattresses, curtains, etc.

• For quickly cleaning larger textile surfaces in the car, such as the boot, foot room, back seat.

• For cleaning hard-to-reach places, such as between the car seats.

• For thoroughly cleaning upholstery and carpet in the car.

• For gently cleaning sensitive surfaces in the car such as the dashboard or centre console.

or

• For gently cleaning sensitive surfaces or delicate items such as those on the workbench.

• Clean the device and plastic accessory parts with a commonly available plastic cleaner.

• Rinse the container and accessories with water, as necessary, and dry them before further use.

1. If necessary, the foam filter / cartridge filter can be cleaned under running water. To do this, remove the foam filter from the filter basket. The cartridge filter can be unlocked and removed by turning it towards the symbol .

2. Do not rub or scrub the foam filter / cartridge filter when cleaning it.

3. Allow the foam filter / cartridge filter to dry completely before using it again.

4. Depending on the filter type, reinsert as follows:

   • Foam filter: Pull the filter over the filter basket and ensure that it is fixed correctly.

   • Cartridge filter: Install the filter on the filter basket, turn it towards the symbol and ensure that it is fixed correctly.

   ---

   

   ---

   

1. Before inserting the cartridge filter, remove the black cover cap and keep it with the foam filter for later use.

2. Put on the cartridge filter and screw it tight.

   ---

   

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

• Declining suction performance 

Cause:

Accessories, the suction hose or the suction tubes are clogged.

Remedy:

• Remove the clog with a suitable aid.

Cause:

The filter bag is full.

Remedy:

• Replace the filter bag.

Cause:

The foam filter / cartridge filter is dirty.

Remedy:

• Clean the foam filter / cartridge filter (see chapter Clean the foam filter / cartridge filter).

Cause:

The foam filter / cartridge filter is damaged.

Remedy:

• Replace the foam filter / cartridge filter.

• WD 2 Plus, KWD 2 

• WD 2 Plus S, KWD 2 S 

• WD 3, KWD 3 

• WD 3 S, KWD 3 S 

• WD 3 P, KWD 3 P 

• WD 3 P S, KWD 3 P S