Read these original instructions and the enclosed safety instructions before using the device for the first time. Act in accordance with them.

Keep both books for future reference or for future owners.

• If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.

• Notify the dealer immediately in the case of shipping damage.

• Check the package contents when unpacking for missing accessories or for damage.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

• This spray retraction device is intended for wet cleaning of upholstery, textile covers, and carpets.

• This device is suitable for commercial use, e.g. in hotels, schools, hospitals, factories, shops, offices, and rental companies.

1. Check the power cord, extension cable and hoses for damage before each start-up.

1. Adv only: Fit the suction pipe onto the floor nozzle and hand-tighten the union nut on the floor nozzle.

2. Adv only: If necessary, slide the D-handle onto the suction pipe and hand-tighten in the desired position. The D-handle is easier to slide on with the help of dishwashing detergent or other lubricant.

3. Adv only: Fit the handle onto the suction pipe and hand-tighten the union nut on the handle.

4. Connect the suction hose to the suction hose connection on the device. Insert the spray hose coupling into the spray hose connection on the device and latch into place.

5. Connect the suction hose to the upholstery nozzle or the handle. Connect the spray hose coupling to the upholstery nozzle or handle and latch into place.

1. Mix fresh water and detergent in a clean container (concentration as specified for the detergent). Dissolve the detergent in the water.

1. Pour the cleaning solution into the fresh water tank. The filling level must not exceed the "MAX" mark.

1. Add defoaming agent (special accessory) to the wastewater container.

1. Connect the mains plug.

2. Press the suction switch to switch on the suction turbine.

3. Press the spray switch to switch on the spray pump.

1. Remove loose dirt from the object to be cleaned.

2. Press the lever on the upholstery nozzle or handle to spray the cleaning solution.

3. Run over the surface to be cleaned in overlapping paths. Pull the nozzle backwards (do not push).

4. Adv only: When interrupting work, the suction pipe (with floor nozzle) can be placed on the carrying handle of the device.

5. When changing the nozzle, the upholstery nozzle can be inserted into the holder for accessories.

1. Switch off the spray switch and the suction switch.

2. Pull out the mains plug.

1. Switch off the suction switch and the spray switch when the wastewater container is full.

2. Remove the cover.

3. Remove the wastewater container from the device and empty it.

1. Switch off the device.

2. Briefly operate the lever on the upholstery nozzle or handle to relieve pressure.

3. Disconnect the upholstery nozzle or handle from the spray/suction hose.

4. Hang the suction hose in the fresh water tank.

5. Press the suction switch to switch on the suction turbine.

6. Suck the fresh water tank empty and switch off the device.

7. Remove the cover.

8. Remove the wastewater container from the device and empty it.

1. Connect the upholstery nozzle or handle (with suction pipe and floor nozzle) to the suction hose.

2. Connect the spray hose coupling to the upholstery nozzle or handle and latch into place.

3. Pour approximately 2 litres of tap water into the fresh water tank. Do not add detergents.

4. Press the spray switch to switch on the spray pump.

5. Hold the upholstery or floor nozzle over a drain.

6. Operate the lever on the upholstery nozzle or handle and flush the device for 1 to 2 minutes.

7. Switch off the device.

1. Flush the device.

2. Drain the wastewater container and clean it under running water.

3. Empty the fresh water tank.

4. Clean the exterior of the device with a damp cloth.

5. To avoid unpleasant smells, remove all water from the device before long downtimes.

6. Let the device dry thoroughly: Remove the cover or move it to the side.

1. Wind the mains cable around the carrying handle of the device and the cover.

   ---

   

2. Store the device in a dry room and secure it against unauthorised use.

1. Spray and vacuum up the cleaning solution in one step.

1. Apply cleaning solution with the suction turbine switched off and let it work for 10 to 15 minutes.

2. Clean the area as with normal soiling.

1. Adv only: Attach the upholstery nozzle instead of the floor nozzle (with suction pipe and handle).

2. Use less detergent for sensitive fabrics and spray the surface at a distance of approx. 200 mm. Then only vacuum.

• Spray heavily soiled areas in advance and allow the cleaning solution to work for 5 to 10 minutes.

• Always work from light to shadow (from window to door).

• Always work from the cleaned to the uncleaned area.

• The more sensitive the covering (oriental bridges, Berber, upholstery fabric) the lower the concentration of detergent.

• Carpets with jute backs can shrink and bleed in colour if the work is too wet.

• Brush wet pile carpets in the direction of the pile after cleaning when wet (e.g. with a fibre brush or scrubber).

• Impregnating after wet cleaning prevents the textile from being quickly soiled again.

• To avoid pressure points or rust stains, do not walk on or furnish the cleaned area until after it has fully dried.

• To improve the cleaning result, rinse the object with clean water after using detergents.

For further information, please request the product information sheet and the EU safety data sheet for the relevant cleaning agent.

1. Wind the mains cable around the carrying handle of the device and the cover. Place the spray/suction hose in the hook. Insert the upholstery nozzle into the accessory holder.

   ---

   

2. Adv only: Place the suction pipe (with floor nozzle) on the carrying handle of the device. Wind up the mains cable and hang it in the cable hook.

   ---

   

3. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respective valid guidelines.

The device may only be operated indoors.

1. Remove the cover.

2. Remove the wastewater container from the device.

3. Pull out the fluff filter.

4. Regularly clean the fluff filter under running water. If very dirty, open the frame and replace the fleece.

1. Unscrew the fresh water filter.

2. Clean the fresh water filter under running water.

1. Unscrew the union nut.

2. Clean the nozzle mouthpiece.

• The device is not working 

• No water emitted from the nozzle 

• Single-sided spray jet 

• Poor suction performance 

• Spray pump is loud 

• Heavy foaming in the wastewater container 

Remedy:

1. Check the socket and the power supply fuse.

2. Check the mains cable and the mains plug of the device.

3. Switch on the device.

Remedy:

1. Fill up the fresh water tank.

2. Check the couplings on the spray hose for correct seating.

3. Clean or replace the nozzle mouthpiece.

4. Clean the fresh water filter.

5. Spray pump defective, contact customer service.

Remedy:

1. Clean the nozzle mouthpiece.

Remedy:

1. Check that the cover is seated correctly.

2. Clean the seal on the cover and the contact surface on the device.

3. Clean the fluff filter.

4. Check the suction hose for clogging; clean if necessary.

Remedy:

1. Refill the fresh water tank.

Remedy:

1. Add defoaming agent (special accessory) to the wastewater container.

If the malfunction cannot be corrected, the device must be checked by the Customer Service department.

• The device is not working 

• No water emitted from the nozzle 

• Single-sided spray jet 

• Poor suction performance 

• Spray pump is loud 

• Heavy foaming in the wastewater container 

Remedy:

1. Check the socket and the power supply fuse.

2. Check the mains cable and the mains plug of the device.

3. Switch on the device.

Remedy:

1. Fill up the fresh water tank.

2. Check the couplings on the spray hose for correct seating.

3. Clean or replace the nozzle mouthpiece.

4. Clean the fresh water filter.

5. Spray pump defective, contact customer service.

Remedy:

1. Clean the nozzle mouthpiece.

Remedy:

1. Check that the cover is seated correctly.

2. Clean the seal on the cover and the contact surface on the device.

3. Clean the fluff filter.

4. Check the suction hose for clogging; clean if necessary.

Remedy:

1. Refill the fresh water tank.

Remedy:

1. Add defoaming agent (special accessory) to the wastewater container.

The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

You can find more detailed information at: www.kaercher.com/dealersearch

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

Product: Spray retraction device

Type: 1.100-xxx

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

EN IEC 63000: 2018

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60335-1

EN 60335-2-68

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN 62233: 2008

-

The signatories act on behalf of and with the authority of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2020/10/01

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

Product: Spray retraction device

Type: 1.100-xxx

S.I. 2008/1597 (as amended)

S.I. 2012/3032 (as amended)

S.I. 2016/1091 (as amended)

EN IEC 63000: 2018

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60335-1

EN 60335-2-68

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN 62233: 2008

-

The signatories act on behalf of and with the authority of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2020/10/01