Logo HD 13/18-4 S Classic HD 17/15-4 S ClassicHD 10/21-4 S Classic HD 10/25-4 S Classic
  • General notes
  • Intended use
    • Water supply limit values
  • Environmental protection
  • Accessories and spare parts
  • Scope of delivery
  • Safety instructions
    • Symbols on the device
    • Safety devices
      • Pressure switch
      • Pressure relief valve
      • Motor circuit breaker
  • Device description
    • Device overview
    • Colour coding
  • Installation
    • Fastening the push handle
    • Installing the oil bleed screw
    • Check the oil level
    • Installing accessories
  • Electrical connection
  • Water connection
    • Connection to a water line
    • Sucking water from a container
    • Vent the device
  • Operation
    • High-pressure operation
    • Operation with detergent
      • Recommended cleaning method
      • After operating with detergent
    • Interrupting operation
    • Continuing operation
    • Finishing operation
  • Transport
  • Storage
    • Storing the device
    • Frost protection
  • Care and service
    • Safety inspection/maintenance contract
    • Maintenance intervals
      • Each time before use
      • Weekly
      • Every 500 operating hours, at least annually
  • Troubleshooting guide

    • The device cannot be started

    • Device does not reach required pressure

    • The water quantity is too low

    • The pump is leaking.

      Up to 3 drops of water per minute are permissible.

    • The pump knocks

    • The detergent dosing volume is too low

    • The foam formation is too low

  • Warranty
  • Technical data
    • HD 10/21-4 S
    • HD 10/25-4 S
    • HD 13/18-4 S
    • HD 17/15-4 S
  • Declaration of Conformity

       HD 13/18-4 S Classic HD 17/15-4 S Classic
      HD 10/21-4 S Classic HD 10/25-4 S Classic

      (08/22)

      General notes

      Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.

      Keep both books for future reference or for future owners.

      Intended use

      Use this high-pressure cleaner only for the following types of work:

      • Cleaning with the high-pressure jet without detergent (e.g. façades, terraces, garden machines)

      • Cleaning with the low-pressure jet and detergent with the cup foam lance available as an accessory (e.g. for cleaning machines, vehicles, buildings, tools)

      We recommend using a rotary nozzle as a special accessory for stubborn soiling.

      The device may only be operated when it is standing on level ground. If the device stands at an angle, the high-pressure pump can be damaged by insufficient lubrication.

      The device must not be operated with Servo Control accessories.

      Water supply limit values

      ATTENTION

      Dirty water

      Premature wear and tear or deposits in the device

      Supply the device using only clean water, or recycled water that does not exceed the specified limit values.

      The following limit values apply to the water supply:

      • pH value: 6.5-9.5

      • Electrical conductivity: Conductivity of fresh water + 1200 µS/cm, maximum conductivity 2000 µS/cm

      • Settleable particles (sample volume 1 l, settling time 30 minutes): < 0.5 mg/l

      • Filterable particles: < 50 mg/l, no abrasive substances

      • Hydrocarbons: < 20 mg/l

      • Chloride: < 300 mg/l

      • Sulphate: < 240 mg/l

      • Calcium: < 200 mg/l

      • Total hardness: < 28 °dH, < 50° TH, < 500 ppm (mg CaCO3/l)

      • Iron: < 0.5 mg/l

      • Manganese: < 0.05 mg/l

      • Copper: < 2 mg/l

      • Active chloride: < 0.3 mg/l

      • Free of unpleasant odours

      Environmental protection

      The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

      Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

      Notes on the content materials (REACH)

      Current information on content materials can be found at: www.kaercher.de/REACH

      Accessories and spare parts

      Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

      Information on accessories and spare parts can be found at www.kaercher.com.

      Scope of delivery

      Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

      Safety instructions

      • It is essential that you read the safety instructions 5.951-949.0 before initial startup.

      • Observe the national regulations for liquid jet cleaners.

      • Observe the national accident prevention regulations. Liquid jet cleaners must be tested regularly. The test result must be recorded in writing.

      • Do not modify the device or accessories.

      Symbols on the device

      The device may not be connected to the public drinking water network.

      The high-pressure jet must not be directed at persons, animals, live electrical equipment or at the device itself. Protect the device from frost.

      Safety devices

      CAUTION

      Missing or modified safety devices

      Safety devices are provided for your own protection.

      Never modify or bypass safety devices.

      The safety devices are set and sealed by the manufacturer. Adjustments are performed only by customer service.

      Pressure switch

      When the trigger on the high-pressure gun is released, the pressure switch switches off the high-pressure pump and the high-pressure jet stops.

      The pump switches on again when the trigger is pulled.

      Pressure relief valve

      When the water quantity is reduced via the pressure and quantity regulator on the trigger gun, the overflow valve opens and part of the water flows back to the suction side of the pump.

      Motor circuit breaker

      The motor circuit breaker shuts off the device if power consumption it too high.

      Device description

      Device overview

      1. Oil drain screw
      2. Oil level gauge
      3. Bleed screw
      4. Type plate
      5. Power switch
      6. Hose hook, cable hook
      7. Push handle
      8. Union nut
      9. High-pressure nozzle
      10. Spray lance EASY!Lock Classic
      11. High-pressure gun EASY!LOCK Classic
      12. Safety latch
      13. Trigger
      14. High-pressure hose EASY!LOCK Classic
      15. Spray lance holder
      16. Accessory compartment
      17. Pressure and quantity regulation
      18. EASY!Lock high-pressure connection
      19. Fine filter
      20. Water connection

      Colour coding

      • Control elements for the cleaning process are yellow.

      • Control elements for maintenance and servicing are light grey.

      Installation

      Fastening the push handle

      1. Plug the push handle connection onto the pipe frame.

        1. Push handle
        2. Pipe frame

      2. Secure both joints with screws, washers and nuts.

        1. Screw M8x45
        2. Washer 8
        3. Push handle
        4. Nut M8, self-locking
        5. Pipe frame

      Installing the oil bleed screw

      1. Unscrew the plug and dispose of it.

        1. Plugs
        2. Bleed screw

      2. Screw in and tighten the bleed screw.

        ATTENTION

        Risk of damage

        If the plug is not replaced with the bleed screw before operation, the high-pressure pump may be damaged.

        Be sure to replace the plug with the bleed screw.

      Check the oil level

      1. Position the device on a level surface.

      2. The oil level must be in the middle of the oil level display.

      3. If necessary, unscrew the bleed screw and top up the oil (see "Technical data").

      Installing accessories

      Note

      The EASY!Lock system connects components quickly and safely via a single turn of the quick-release thread.

      1. Plug the high-pressure nozzle onto the spray lance.

      2. Fit the union nut and hand-tighten (EASY!Lock).

      3. Connect the spray lance to the high-pressure gun and hand-tighten (EASY!Lock).

      4. Connect the high-pressure hose to the high-pressure gun and high-pressure connection of the device and tighten hand-tight (EASY!Lock).

      Electrical connection

      DANGER

      Risk of injury from electric shock

      Use a plug to connect the device to the mains grid. Permanent connection to the mains grid is prohibited. The plug is used for mains isolation.

      Only connect the device to an AC power source.

      Use an extension cable with sufficient diameter (see "Technical data").

      Unwind the extension cable completely from the cable drum.

      1. Unwind the mains cable and place on the ground.

      2. Plug the mains plug into the socket.

      Water connection

      Connection to a water line

      WARNING

      Return flow of dirty water into the drinking water network

      Health risk

      Observe the regulations of your water supply company.

      According to applicable regulations, the device must never be used with the drinking water network without a system separator. Use a system separator from KÄRCHER or a system separator as per EN 12729 Type BA. Water that has flowed through a system separator is classified as undrinkable. Always connect the system separator to the water supply and never directly to the water connection on the device.

      1. Check the supply pressure, supply temperature and supply volume of the water supply (see chapter Technical data).

      2. Connect the system separator to the water connection of the device using a water supply hose (for the requirements placed on the water supply hose see chapter Technical data).

      3. Open the water inlet.

      Sucking water from a container

      1. Screw the suction hose with filter onto the water connection (for the order number see chapter Technical data).

      2. Vent the device (see chapter Vent the device).

      Vent the device

      1. Unscrew the high-pressure nozzle from the spray lance.

      2. Allow the device to run until the escaping water is free of air bubbles.

      3. In the case of venting problems, allow the device to run for 10 seconds and then switch it off. Repeat the procedure several times.

      4. Switch off the device.

      5. Screw the high-pressure nozzle onto the spray lance.

      Operation

      DANGER

      High-pressure water jet

      Risk of injury

      Never fasten the trigger in the actuated position.

      Push the safety latch of the high-pressure gun forwards every time before starting work with the device.

      Hold the high-pressure gun and spray lance with both hands.

      WARNING

      Defective device and accessories, defective supply lines and connections

      Danger of injury

      The device may only be operated when in a correct operating condition.

      High-pressure operation

      Note

      The device is equipped with a pressure switch. The motor only starts up when the high-pressure gun is open.

      1. Set the power switch to "1".

      2. Unlock the trigger gun by pushing the safety latch to the rear.

      3. Pull the trigger of the high-pressure gun.

      4. Adjust the working pressure and water quantity by turning (infinitely adjustable) the pressure and quantity regulator (+/-)

      Operation with detergent

      WARNING

      Incorrect handling of detergents

      Health risk

      Adhere to the safety instructions stated on the detergent packaging.

      ATTENTION

      Unsuitable detergents

      Damage to the device and the objects to be cleaned

      Use only detergents approved by KÄRCHER.

      Observe the dosing recommendations and notes provided with the detergent.

      Use detergents sparingly to help conserve the environment.

      Note

      KÄRCHER detergents ensure fault-free operation. Ask us for a consultation, request our catalogue or our detergent information sheets.

      Note

      A cup foam lance (optional)is needed for operating with detergent.

      1. Unscrew the container.

        1. Container
        2. Foam nozzle
        3. High-pressure gun
        4. Suction hose
        5. GateDetergent mixing: 3=high, 2=medium, 1=low

      2. Plug the desired gate into the suction hose.

      3. Fill the detergent into the container.

      4. Screw the container onto the foam nozzle.

      5. Disconnect the spray lance from the high-pressure gun.

      6. Connect the cup foam lance to the high-pressure gun and hand-tighten.

      7. Start up the high-pressure cleaner.

      Recommended cleaning method

      1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).

      2. Rinse off the loosened dirt with the high-pressure jet.

      After operating with detergent

      The cup foam lance must be flushed after use to prevent the formation of detergent deposits.

      1. Unscrew the container.

      2. Pour the remaining detergent back into the original packaging.

      3. Fill the container with clear water.

      4. Screw the container onto the cup foam lance nozzle.

      5. Operate the cup foam lance for approx. 1 minute to flush the detergent residue.

      6. Empty the container.

      Interrupting operation

      1. Close the high-pressure gun.

        The device switches off.

      2. Push the safety latch forwards.

        The high-pressure gun is secured.

      Continuing operation

      1. Push the safety latch backwards.

        The high-pressure gun is unlocked.

      2. Open the high-pressure gun.

        The device switches on.

      Finishing operation

      1. Close the water inlet.

      2. Open the high-pressure gun.

      3. Set the trigger to "I/ON" and allow the device to run for 5-10 seconds.

      4. Close the high-pressure gun.

      5. Set the power switch to "0/OFF".

      6. Pull the mains plug out of the socket only when your hands are dry.

      7. Remove the water inlet.

      8. Open the high-pressure gun until the device is completely depressurised.

      9. Push the safety latch forwards.

        The high-pressure gun is secured.

      Transport

      CAUTION

      Failure to observe the weight

      Risk of injury and damage

      Be aware of the weight of the device during transport and storage.

      • Transporting the device in vehicles: Secure the device in accordance with the respectively applicable guidelines to prevent it from slipping or overturning.

      • Transporting the device over longer distances: Pull or push the device using the push handle.

      Storage

      CAUTION

      Failure to observe the weight

      Risk of injury and damage

      Be aware of the weight of the device during transport and storage.

      Store the device indoors only.

      Storing the device

      1. Place the spray lance with the high-pressure gun on the two spray lance supports.

      2. Roll up the mains cable and hang it over the cable holders.

      3. Wind up the high-pressure hose and hang it on the hose hook.

      Frost protection

      ATTENTION

      Frost

      Destruction of the device through freezing water

      Drain all water from the device.

      Store the device in a frost-free location.

      If frost-free storage is not possible:

      1. Drain the water.

      2. Pump commonly available anti-freeze through the device.

        Note

        Use commonly available, Glycol-based vehicle anti-freeze. Observe the handling instructions of the anti-freeze manufacturer.

      3. Allow the device for run for a maximum of 1 minute until the pump and lines are empty.

      Care and service

      DANGER

      Inadvertently starting up device

      Risk of injury, electric shock

      Switch off the device immediately and unplug the mains plug before performing work.

      Note

      Old oil may only be disposed of at designated collection points. Please dispose of any old oil at these locations. Polluting the environment with old oil is punishable by law.

      Safety inspection/maintenance contract

      You can agree on regular safety inspections or close a maintenance contract with your dealer. Please seek advice on this.

      Maintenance intervals

      Each time before use

      • Check the mains cable for damage.

        Have a damaged cable replaced immediately by the authorised Customer Service or a qualified electrician.

      • Check the high-pressure hose for damage.

        Immediately replace a damaged high-pressure hose.

      • Check the device for leaks.

        3 drops of water per minute are permissible. Contact Customer Service in the case of more serious leaks.

      Weekly

      • Check the oil level. Contact Customer Service immediately if the oil is milky (water in oil).

      • Clean the fine filter.

        1. Filter housing
        2. Fine filter
        3. Connection nozzle
        4. Union nut

        1. Unscrew the union nut.

        2. Pull out the connection nozzle.

        3. Pull the fine filter out of the filter housing.

        4. Rinse the fine filter with clear water or blow it out with compressed air.

        5. Insert the fine filter into the filter housing.

        6. Attach the connection nozzle.

        7. Screw on the union nut and hand-tighten.

      Every 500 operating hours, at least annually

      • Have the device serviced by Customer Service.

      • Change the oil in the high-pressure pump.

        1. Bleed screw
        2. Oil level gauge
        3. Oil drain screw

        1. Unscrew the oil drain plug.

        2. Drain the oil into a suitable collection container.

        3. Screw in and tighten the oil drain screw.

        4. Unscrew the bleed screw.

        5. Fill in new oil slowly so that air bubbles can escape. See the "Technical data" section for the oil volume and type.

        6. Re-install the bleed screw.

      Troubleshooting guide

      DANGER

      Inadvertently starting up device, touching live components

      Risk of injury, electric shock

      Switch off the device before performing any work on the device.

      Remove the mains plug.

      Have all checks and work on electrical parts performed by a qualified electrician.

      In case of any malfunctions not mentioned in this chapter, contact the authorised Customer Service.

      • The device cannot be started 

      • Device does not reach required pressure 

      • The water quantity is too low 

      • The pump is leaking.Up to 3 drops of water per minute are permissible. 

      • The pump knocks 

      • The detergent dosing volume is too low 

      • The foam formation is too low 

      The device cannot be started

      Remedy:

      1. Check the mains cable for damage.

      2. Check the mains voltage.

      3. If the device overheats:

        1. Set the power switch to "0/OFF".

        2. Allow the device to cool for at least 15 minutes.

        3. Set the trigger to the "I/ON" position.

      4. Contact Customer Service in the case of electrical faults.

      Device does not reach required pressure

      Remedy:

      1. Check that the high-pressure nozzle is the right size (see chapter "Technical data").

      2. Clean or replace the nozzle.

      3. Vent the device (see chapter "Venting the water connection/device.").

      4. Clean the fine filter, replace if necessary (see chapter "Care and Maintenance/Weekly").

      5. Check the water supply volume (compare with the required volume specified in the "Technical data" chapter).

      6. Contact Customer Service if necessary.

      The water quantity is too low

      Remedy:

      1. When using a long high-pressure hose or a high-pressure hose with a small diameter, fit a larger high-pressure nozzle to the spray lance.

      The pump is leaking.

      Up to 3 drops of water per minute are permissible.

      Remedy:

      • In case of more serious leaks, have the device checked by Customer Service.

      The pump knocks

      Remedy:

      1. Check the water supply volume (compare with the required volume specified in the "Technical data" chapter).

      2. Vent the device (see chapter "Venting the water connection/device.").

      3. Clean the fine filter, replace if necessary (see chapter "Care and Maintenance/Weekly").

      4. Contact Customer Service if necessary.

      The detergent dosing volume is too low

      Remedy:

      1. Check that the cup foam lance used matches the flow rate of the device.

      2. Refill the cup of the cup foam lance.

      3. Plug a larger gate onto the suction hose.

      4. Check the suction hose and cup foam nozzle for detergent deposits. Remove deposits using lukewarm water.

      5. Contact Customer Service if necessary.

      The foam formation is too low

      Remedy:

      1. Check that the cup foam lance used matches the flow rate of the device.

      2. Check the suction hose and cup foam lance for detergent deposits. Remove deposits using lukewarm water.

      3. Contact Customer Service if necessary.

      Warranty

      The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

      (See overleaf for the address)

      Technical data

      • HD 10/21-4 S 

      • HD 10/25-4 S 

      • HD 13/18-4 S 

      • HD 17/15-4 S 

      HD 10/21-4 S

      Country variant
      Country
      EU
      Electrical connection
      Voltage
      400 V
      Phase
      3 ~
      Frequency
      50 Hz
      Maximum permissible mains grid impedance
      - Ω
      Power rating
      8,0 kW
      Degree of protection
      IPX5
      Power protection (slow-blow, char. C)
      16 A
      Extension cable, 10 m
      2,5 mm2
      Extension cable, 30 m
      4 mm2
      Water connection
      Feed pressure (max.)
      1 MPa
      Input temperature (max.)
      60 °C
      Input amount (min.)
      20 l/min
      Suction height (max.)
      0,5 m
      Minimum water supply hose length
      7,5 m
      Minimum water supply hose diameter
      1 in
      Suction filter order number
      4.730-012.0
      Device performance data
      Nozzle size of standard nozzle
      050
      Water operating pressure with standard nozzle
      21 MPa
      Operating pressure (max.)
      27 MPa
      Water flow rate
      16,7 l/min
      High-pressure gun recoil force
      57 N
      Dimensions and weights
      Typical operating weight
      60 kg
      Length
      720 mm
      Width
      637 mm
      Height
      1080 mm
      Oil volume
      0,65 l
      Oil type
      15W40 Type
      Determined values in acc. with EN 60335-2-79
      Hand-arm vibration value
      2,8 m/s2
      Uncertainty K
      0,8 m/s2
      Sound pressure level LpA
      69 dB(A)
      Uncertainty KpA
      3 dB(A)
      Sound power level LWA + uncertainty KWA
      86 dB(A)

      HD 10/25-4 S

      Ländervariante
      Land
      EU
      Elektrischer Anschluss
      Spannung
      400 V
      Phase
      3 ~
      Frequenz
      50 Hz
      Maximal zulässige Netzimpedanz
      0.0452 +j0.0283 Ω
      Anschlussleistung
      8,8 kW
      Schutzart
      IPX5
      Netzabsicherung (träge, Char. C)
      16 A
      Verlängerungskabel 10 m
      2,5 mm2
      Verlängerungskabel 30 m
      4 mm2
      Wasseranschluss
      Zulaufdruck (max.)
      1 MPa
      Zulauftemperatur (max.)
      60 °C
      Zulaufmenge (min.)
      20 l/min
      Ansaughöhe (max.)
      0,5 m
      Mindestlänge Wasserzulaufschlauch
      7,5 m
      Mindestdurchmesser Wasserzulaufschlauch
      1 in
      Saugfilter Bestellnummer
      4.730-012.0
      Leistungsdaten Gerät
      Düsengröße der Standarddüse
      045
      Betriebsdruck Wasser mit Standarddüse
      25 MPa
      Betriebsüberdruck (max.)
      31 MPa
      Fördermenge, Wasser
      16,7 l/min
      Rückstoßkraft der Hochdruckpistole
      63 N
      Maße und Gewichte
      Typisches Betriebsgewicht
      67 kg
      Länge
      720 mm
      Breite
      637 mm
      Höhe
      1080 mm
      Ölmenge
      0,65 l
      Ölsorte
      15W40 Typ
      Ermittelte Werte gemäß EN 60335-2-79
      Hand-Arm-Vibrationswert
      3,7 m/s2
      Unsicherheit K
      0,9 m/s2
      Schalldruckpegel LpA
      74 dB(A)
      Unsicherheit KpA
      3 dB(A)
      Schallleistungspegel LWA + Unsicherheit KWA
      91 dB(A)

      HD 13/18-4 S

      Ländervariante
      Land
      EU
      Elektrischer Anschluss
      Spannung
      400 V
      Phase
      3 ~
      Frequenz
      50 Hz
      Maximal zulässige Netzimpedanz
      0.0452 +j0.0283 Ω
      Anschlussleistung
      8,8 kW
      Schutzart
      IPX5
      Netzabsicherung (träge, Char. C)
      16 A
      Verlängerungskabel 10 m
      2,5 mm2
      Verlängerungskabel 30 m
      4 mm2
      Wasseranschluss
      Zulaufdruck (max.)
      1 MPa
      Zulauftemperatur (max.)
      60 °C
      Zulaufmenge (min.)
      25 l/min
      Ansaughöhe (max.)
      0,5 m
      Mindestlänge Wasserzulaufschlauch
      7,5 m
      Mindestdurchmesser Wasserzulaufschlauch
      1 in
      Saugfilter Bestellnummer
      4.730-012.0
      Leistungsdaten Gerät
      Düsengröße der Standarddüse
      075
      Betriebsdruck Wasser mit Standarddüse
      18 MPa
      Betriebsüberdruck (max.)
      24 MPa
      Fördermenge, Wasser
      21,67 l/min
      Rückstoßkraft der Hochdruckpistole
      69 N
      Maße und Gewichte
      Typisches Betriebsgewicht
      67 kg
      Länge
      720 mm
      Breite
      637 mm
      Höhe
      1080 mm
      Ölmenge
      0,65 l
      Ölsorte
      15W40 Typ
      Ermittelte Werte gemäß EN 60335-2-79
      Hand-Arm-Vibrationswert
      2,9 m/s2
      Unsicherheit K
      0,8 m/s2
      Schalldruckpegel LpA
      74 dB(A)
      Unsicherheit KpA
      3 dB(A)
      Schallleistungspegel LWA + Unsicherheit KWA
      91 dB(A)

      HD 17/15-4 S

      Ländervariante
      Land
      EU
      Elektrischer Anschluss
      Spannung
      400 V
      Phase
      3 ~
      Frequenz
      50 Hz
      Maximal zulässige Netzimpedanz
      0.0452 +j0.0283 Ω
      Anschlussleistung
      9,0 kW
      Schutzart
      IPX5
      Netzabsicherung (träge, Char. C)
      16 A
      Verlängerungskabel 10 m
      2,5 mm2
      Verlängerungskabel 30 m
      4 mm2
      Wasseranschluss
      Zulaufdruck (max.)
      1 MPa
      Zulauftemperatur (max.)
      60 °C
      Zulaufmenge (min.)
      31,6 l/min
      Ansaughöhe (max.)
      0,5 m
      Mindestlänge Wasserzulaufschlauch
      7,5 m
      Mindestdurchmesser Wasserzulaufschlauch
      1 in
      Saugfilter Bestellnummer
      4.730-012.0
      Leistungsdaten Gerät
      Düsengröße der Standarddüse
      105
      Betriebsdruck Wasser mit Standarddüse
      15 MPa
      Betriebsüberdruck (max.)
      21 MPa
      Fördermenge, Wasser
      28,33 l/min
      Rückstoßkraft der Hochdruckpistole
      85 N
      Maße und Gewichte
      Typisches Betriebsgewicht
      73 kg
      Länge
      720 mm
      Breite
      637 mm
      Höhe
      1080 mm
      Ölmenge
      1,2 l
      Ölsorte
      15W40 Typ
      Ermittelte Werte gemäß EN 60335-2-79
      Hand-Arm-Vibrationswert
      3,0 m/s2
      Unsicherheit K
      0,8 m/s2
      Schalldruckpegel LpA
      76 dB(A)
      Unsicherheit KpA
      3 dB(A)
      Schallleistungspegel LWA + Unsicherheit KWA
      93 dB(A)

      Declaration of Conformity

      EU Declaration of Conformity

      We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

      Product: High-pressure cleaner

      Type: 1.367-xxx

      Currently applicable EU Directives

      2000/14/EC

      2006/42/EC (+2009/127/EC)

      2011/65/EU

      2014/30/EU

      2009/125/EC

      Commission Regulation(s)

      (EU) 2019/1781

      Harmonised standards used

      EN 60335-1

      EN 60335-2-79

      EN IEC 63000: 2018

      EN 55014-1: 2017 + A11: 2020

      EN 55014-2: 1997 + A1: 2001 + A2: 2008

      EN 61000-3-2: 2014

      EN 61000-3-3: 2013

      HD 9/20-4 S ClassicHD 10/21-4 S Classic

      EN 61000-3-11: 2000

      HD 13/18-4 S ClassicHD 10/25-4 S ClassicHD 17/15-4 S Classic

      EN 62233: 2008

      National standards used

      -

      Applied conformity evaluation method

      2000/14/EG: Annex V

      Sound power level dB(A)

       

      Measured:

      Guaranteed:

      HD 10/21-4 S Classic

      Measured: 84

      Guaranteed: 86

      HD 13/18-4 S Classic

      Measured: 89

      Guaranteed: 91

      HD 10/25-4 S Classic

      Measured: 89

      Guaranteed: 91

      HD 17/15-4 S Classic

      Measured: 91

      Guaranteed: 93

      The signatories act on behalf of and with the authority of the company management.

      Documentation supervisor:

      S. Reiser

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Ph.: +49 7195 14-0

      Fax: +49 7195 14-2212

      Winnenden, 2022/08/01

      Declaration of Conformity (UK)

      We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

      Product: High-pressure cleaner

      Type: 1.367-xxx

      Currently applicable UK Regulations

      S.I. 2001/1701 (as amended)

      S.I. 2008/1597 (as amended)

      S.I. 2012/3032 (as amended)

      S.I. 2016/1091 (as amended)

      S.I. 2010/2617 (as amended)

      Commission Regulation(s)

      (EU) 2019/1781

      Designated standards used

      EN 60335-1

      EN 60335-2-79

      EN IEC 63000: 2018

      EN 55014-1: 2017 + A11: 2020

      EN 55014-2: 1997 + A1: 2001 + A2: 2008

      EN 61000-3-2: 2014

      EN 61000-3-3: 2013

      HD 9/20-4 S ClassicHD 10/21-4 S Classic

      EN 61000-3-11: 2000

      HD 13/18-4 S ClassicHD 10/25-4 S ClassicHD 17/15-4 S Classic

      EN 62233: 2008

      National standards used

      -

      Applied conformity assessment procedure

      S.I. 2001/1701 (as amended): Schedule 8

      Sound power level dB(A)

       

      Measured:

      Guaranteed:

      HD 10/21-4 S Classic

      Measured: 84

      Guaranteed: 86

      HD 13/18-4 S Classic

      Measured: 89

      Guaranteed: 91

      HD 10/25-4 S Classic

      Measured: 89

      Guaranteed: 91

      HD 17/15-4 S Classic

      Measured: 91

      Guaranteed: 93

      The signatories act on behalf of and with the authority of the company management.

      Documentation supervisor:

      S. Reiser

      Alfred Kärcher SE & Co. KG

      Alfred-Kärcher-Str. 28 - 40

      71364 Winnenden (Germany)

      Ph.: +49 7195 14-0

      Fax: +49 7195 14-2212

      Winnenden, 2022/08/01

      <BackPage>

       



      </BackPage>