Observe all basic precautions when using the device, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE

This device is exclusively intended for private household use.

SAVE THESE INSTRUCTIONS

The power switch stops you from operating the device unintentionally.

If the lever on the trigger gun is released, the pressure switch switches the pump off; the low-pressure jet stops. If the lever is pressed, the pump switches on again.

The motor circuit breaker shuts off the device if power consumption it too high.

For home use only!

The low-pressure cleaner is intended for cleaning machines, vehicles, tools, facades, terraces, garden machines, pets, etc. with a low-pressure water jet without the addition of detergents.

The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this device.

Warning information should be emphasized and understood.

If the operator is not fluent in English, the manufacturer’s instructions and warnings shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner, making sure that the operator comprehends its contents.Owner and/or user must study and maintain for future reference the manufacturer’s instructions.

The scope of delivery for the appliance is shown on the packaging. During unpacking, check the contents for completeness. If any accessories are missing or in the event of any shipping damage, please contact customer service, see section Customer Service.

Your device must be registered in order to help with any questions or issues that you have. You can register your device at www.karcher-register.com if located in the U.S.A., www.karcher.ca if located in Canada, or www.karcher.com/mx if located in Mexico.

In the case of a warranty claim, you can contact customer support. Please see the contact information listed below for either the USA, Canada or Mexico. You MUST provide your proof of purchase in order to file a warranty claim either via e-mail, phone or fax.

You can contact our Customer Service department by phone at 1-800-537-4129 or via the website at www.karcher-help.com.

You can contact our Customer Service department by phone at 1-800-465-4980 or via the website at www.karcher.com/ca/support.

You can contact our Customer Service department by phone at 01-800-024-1313 or via the website at www.karcher.com/mx.

1. Place the device on a level surface.

1. Release the cover on the right-hand side from the charging socket and turn it downwards.

2. Insert the charging plug of the charger into the charging socket.

3. Plug the charger into a mains socket.

   The battery is being charged.

   ---

   

   Note

   The charge level indicator flashes during the charging process. When the battery is fully charged, it lights up continuously. For the charging time when the battery is empty, see chapter Technical data.

4. When the battery is fully charged, unplug the charger or the 12 V charger in the reverse order.

1. Fold the carrying handle of the device forwards.

   1. Lift the carrying handle of the device and the carrying handle of the water reservoir together.

   2. Pivot the carrying handle of the device forwards.

   ---

   

2. Remove the water reservoir vertically upwards using the carrying handle of the water reservoir.

   ---

   

3. Open the lid on the water reservoir and fill the water reservoir with clear water.

   ---

   

4. Remove the trigger gun from the device.

   ---

   

5. Place the water reservoir onto the device.

   Note

   Make sure that the low-pressure hose is in the recess and is not pinched.

1. Press the power switch.

   ---

   

2. Press the lever of the trigger gun.

Approx. 2 minutes before the end of the operating time (see chapter Technical data), the charge level indicator starts to flash.

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).

2. Rinse off the loosened dirt with the low-pressure jet.

1. Release the lever of the trigger gun.

After approx. 5 minutes without operation, the device switches off automatically.

1. Remove the water reservoir.

2. Switch on the device.

3. Operate the lever of the trigger gun until no more water escapes.

4. Release the lever of the trigger gun.

5. Empty the water reservoir completely.

6. Place the water reservoir onto the device.

1. Lift and carry the device by the carrying handle of the device.

1. Stow or secure the device in such a way that it cannot slip or be thrown around in the vehicle when accelerating, braking, cornering or in the event of an accident.

1. Place the device on a level surface.

2. Store the device within the permitted ambient temperature (see chapter Technical data).

1. Empty the device (see chapter Finishing operation).

Clean the valve opener and the fine filter regularly.

1. Remove the water reservoir, see chapter Water supply.

2. Remove the valve opener using suitable pliers.

   ---

   

3. Remove the fine filter using suitable pliers.

4. Clean the valve opener and the fine filter under running water.

5. Insert the fine filter and the valve opener into the device.

   ATTENTION

   The pins on the fine filter and valve opener must point upwards.

6. Place the water reservoir onto the device.

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorized Customer Service.

• The device does not run 

• Device does not reach required pressure 

• Strong pressure fluctuations 

• The device is leaking 

Cause:

The charging state of the battery is too low.

Remedy:

1. Check the charging state of the battery, charge the battery if necessary.

Cause:

The motor is overloaded, the motor circuit breaker has tripped.

Remedy:

1. Switch off the device.

2. Allow the device to cool down.

3. Switch on the device and put it into operation.

Cause:

The ambient temperature is outside the permissible range (see chapter Technical data) and the motor circuit breaker has tripped.

Remedy:

1. Switch off the device.

2. Allow the device to cool down or heat up.

3. Switch on the device and put it into operation.

   If the malfunction occurs several times, contact the authorized Customer Service.

Cause:

Water shortage

Remedy:

1. Fill the water reservoir with clear water.

Cause:

The valve opener or fine filter are dirty.

Remedy:

1. Clean the valve opener and the fine filter (see chapter Cleaning the valve opener / fine filter).

Cause:

The valve opener is installed incorrectly.

Remedy:

1. Insert the valve opener into the device so that the pin points upwards.

Cause:

The flat jet nozzle is dirty.

Remedy:

1. Clean the flat jet nozzle: Remove the dirt from the nozzle bore with a needle and rinse with water from the front.

Cause:

Water shortage

Remedy:

1. Fill the water reservoir with clear water.

Cause:

A slight leakage in the device is due to technical reasons.

Remedy:

1. In case of severe leakage, contact an authorized Customer Service center.