Before using the device read the enclosed original operating instructions of this device, the battery pack and the charger. Act in accordance with them.

Keep these documents for future reference or for future owners.

• If the operating instructions are not observed, the device can be damaged and dangers could arise for the operator and other persons.

• Notify the dealer immediately in the case of shipping damage.

• Depending on the device variant, the battery pack and charger are included in the scope of delivery.

• Check the package contents when unpacking for missing accessories or for damage.

You can find a QR Code® for calling up an application video in:

---

---

QR-Code^® is a registered trademark of DENSO WAVE INCORPORATED.

Only use the device in private households.

The device is intended for use as a spray extraction cleaner for cleaning car interiors and upholstery textiles indoors in accordance with the descriptions given in these operating instructions and the safety instructions.

For operation, a battery pack of the KÄRCHER Battery Power (+) platform with 18 V nominal voltage and a suitable KÄRCHER charger with 18 V nominal voltage is required, which are not included in the scope of delivery.

Battery packs/chargers that are not supplied in the scope of delivery or are additionally required are available as accessories.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

Our local KÄRCHER branch will be happy to help you if you have any questions or problems with the device.

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

You can find more detailed information at: www.kaercher.com/dealersearch

Depending on the model selected, there are differences in the equipment. The specific equipment is described on the device packaging.

---

1. Spray/suction hose connection
2. Power switch (1 (ON) / 0 (OFF))
3. Waste water tank with lid
4. Fresh water tank with lid
5. Fuel cap
6. Carrying handle
7. Holder for accessories
8. Storage for sponge, brush, detergent bag
9. Battery pack mounting
10. *Rechargeable battery pack
11. Spray/suction hose with rotating handle
12. Upholstery nozzle for spray extraction
13. Crevice nozzle for spray extraction
14. Detergent RM 519 (100 ml)
15. *Charger

* optional

1. Charging the battery pack (see operating instructions and safety instructions for the battery pack and the charger).

1. Press the spray/suction hose into the spray/suction hose connection on the device until it latches into place.

   • For removal, press the latch and pull the spray/suction hose out.

   ---

   

2. Connect the upholstery nozzle or crevice nozzle to the handle, depending on the application case.

   • To separate the upholstery nozzle and crevice nozzle, press the catch on the handle and pull the spray/suction hose off.

   ---

   

   ---

   

Filling the water reservoir directly on the device

1. Pull the tank cap upwards and turn sideways. Dose the detergent according to the specifications and then fill the tank with water up to the "MAX" mark.

   ---

   

2. Close the tank cap.

Removing the water tank for filling

1. Pull out the water tank vertically upwards by the recessed grip.

   ---

   

2. Pull the tank cap upwards, turn it sideways and fill the water tank with detergent and tap water up to the "MAX" mark.

   ---

   

   or

   Unlock the tank lid, remove it and fill with detergent and tap water up to the "MAX" mark.

   ---

   

3. Close the tank cap or fit the tank lid making sure that it is firmly seated.

4. Fit the water tank down to the bottom of the device.

• Push the battery pack into the battery pack mount from above until the battery pack latches into place.

  ATTENTION

  Only use battery packs from the KÄRCHER Battery Power (+) platform with 18 V nominal voltage.

  ---

  

1. Turn the power switch to position 1 (ON).

   ---

   

   The suction turbine and pump start.

1. Fill the fresh water tank with detergent and water, see chapterFilling the fresh water tank .

2. Fit the battery pack, see chapter Fitting the battery pack.

3. Switch the device on, see chapter Switching on the device.

4. Press the lever on the handle to spray the cleaning solution.

   ---

   

5. Pull the upholstery nozzle backwards over the surface to be cleaned in overlapping paths, do not push.

Note

When the wastewater container is full, a float switch closes the suction opening and the device runs at a higher speed.

6. Switch off the device immediately and empty the waste water tank, see chapter Emptying the waste water tank.

1. Turn the power switch to position 1 (ON).

   ---

   

   The suction turbine and pump start.

2. Press the lever for spraying.

   The cleaning solution is sprayed on.

   ---

   

3. Release the lever for spraying and vacuum the residues of the cleaning solution.

4. After cleaning, clean the upholstery with clean, warm water and impregnate if desired.

1. Turn the power switch to position 1 (ON).

   ---

   

   The suction turbine and pump start.

2. Press the lever for spraying.

   ---

   

   Cleaning solution is sprayed.

3. Turn the power switch to position 0 (OFF).

   ---

   

4. Allow the cleaning solution to act for at least 5 minutes.

5. Turn the power switch to position 1 (ON).

   The suction turbine and pump start.

   ---

   

6. Suck off any residues of the cleaning solution.

7. Repeat the procedure if necessary.

8. After cleaning, clean the upholstery with clear, warm water and impregnate if desired.

1. Turn the power switch to position 0 (OFF).

   ---

   

2. Empty the waste water tank, see chapter Emptying the waste water tank.

3. Fill the fresh water tank with tap water up to the "MAX" mark, see chapter Filling the fresh water tank.

4. Connect the spray/suction hose to the crevice nozzle.

5. Open the tank cap and insert the crevice nozzle completely into the opening.

   ---

   

6. Turn the power switch to position 1 (ON) and simultaneously press and hold down the spray lever on the handle.

   ---

   

   The rinsing process is finished as soon as the fresh water tank is completely empty.

7. Turn the power switch to position 0 (OFF).

   ---

   

8. Remove the battery pack, see chapter Removing the battery pack.

9. Charge the battery pack if necessary.

10. Empty the waste water tank, see chapter Emptying the waste water tank.

11. Thoroughly rinse the waste water tank with clear water.

12. If necessary, e.g. if the sieve in the fresh water tank is contaminated, rinse the fresh water tank with clear water, see chapter Cleaning the waste water tank cap and separator.

13. Disconnect the accessories from the device.

14. To remove any remaining liquid in the spray/suction hose:

    1. Press the catch and remove the spray/suction hose from the device.

    2. Press the lever on the handle and let the liquid flow out.

       Note

       To allow the liquid to dry completely, do not wrap the spray/suction hose around the device to dry.

       Note

       To avoid puddles in the living area (e.g. on carpet, parquet), let the remaining liquid run in a suitable container (e.g. sink, bucket).

15. Rinse the upholstery nozzle with tap water and let the device dry with the other accessories.

16. Stow the device in the "drying position" (with the two tank lids slightly open so that any remaining liquid can dry without leaving any residue).

1. Pull out the dirty water tank vertically upwards by the recessed grip.

   ---

   

2. Unlock the two side ones tank caps, remove the filler cap and dispose of waste water.

   ---

   

3. When continuing the cleaning work: Replace the filler cap, making sure that it is firmly seated. Insert the waste water tank down to the bottom of the device.

4. At the end of the cleaning work: Stow the device in the "drying position" (the filler cap is slightly open and any remaining liquid can dry without leaving any residue).

1. Remove the waste water tank from the device, see chapter Emptying the waste water tank

2. Remove the tank lid from the tank and remove the separator.

3. Carefully clean the tank lid and separator with a damp cloth.

4. Carefully remove moisture with a dry cloth.

   ---

   

5. Fit the tank lid and separator together, fasten on the tank and fit them back into the device.

• Push the battery pack upwards and remove it from the device.

  ---

  

• Fasten the crevice nozzle to the accessory holder.

• Wrap the suction hose around the device and fasten it to the other accessory holder with the upholstery nozzle.

  ---

  

  ---

  

• Store the device in a dry and frost-free room.

1. Lift and carry the device by the carrying handle.

1. Secure the device against slipping and tipping over.

1. Clean the device and accessory parts made of plastic with a commonly available plastic cleaner.

2. Rinse the container and accessories with water as necessary and dry them thoroughly before further use.

3. Regularly check the battery terminals for soiling and clean them as necessary.

1. Remove the fresh water tank from the device, see Chapter Filling the fresh water tankFilling the fresh water tank.

2. Rinse out the fresh water tank with clean water.

3. Insert the fresh water tank back into the device.

• Device not running 

• Device switches off automatically 

• No water emitted from the nozzle 

• Poor suction performance 

Cause:

Battery pack not correctly seated in the battery pack mounting.

Remedy:

1. Push the battery pack into the battery pack mounting until it latches into place.

   Note

   If necessary, remove the battery pack again and reinsert it until it latches into place.

Cause:

Charging state of the battery pack (see display) too low.

Remedy:

1. Charge the battery pack.

Cause:

Defective battery pack or charger.

Remedy:

1. Replace the battery pack or charger.

Cause:

Device/battery pack overheated.

Remedy:

• Wait until the device/battery pack has cooled down.

Cause:

Grids of the waste water tank lid are contaminated or wet.

Remedy:

• Clean/dry the grids.

Remedy:

• Fill up the fresh water tank.

Remedy:

• Check connection of accessory nozzle and spray/suction hose for correct fit.

Remedy:

• Clean the fresh water filter.

Remedy:

• Spray pump defective, contact customer service.

Cause:

Upholstery nozzle, crevice nozzle or suction hose are blocked.

Remedy:

• Check the upholstery nozzle, crevice nozzle and suction hose for blockages and clean if necessary.