Use the floor cleaner exclusively for cleaning hard floors in your private household and only on waterproof hard floors.

No water-sensitive floor coverings such asuntreated cork floors, since the moisture can penetrate and damage the floor.

The device is suitable for cleaning PVC, linoleum, tiles, stone, oiled and waxed parquet, laminate and all water-resistant floor coverings.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

Further information can be found at: www.kaercher.com/dealersearch

Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".

Read this safety chapter and these original instructions before using the device for the first time. Act in accordance with them. Keep the original instructions for future reference or for future owners.

• In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.

• Warnings and information notices attached to the device provide important information for hazard-free operation.

Use the following adapter:

---

The warning for not cleaning the floor head under running water is located: on the underside of the floor head.

• The symbols for the device cleaning mode after finishing work are:

  • engraved in the bowl of the cleaning station,

  • located on the back of the fresh water tank as a label.

• The symbols for unlocking the waste water tank / parking station are located:

  • as a label on the unlocking button for the waste water tank/parking station.

The application is described in the chapter Floor head cleaning by means of rinsing process.

To be able to use all available functions, we recommend connecting the device to the Kärcher Home & Garden app. To do this, the KÄRCHER Home & Garden app must be^® downloaded to a mobile device with Bluetooth wireless technology.

The Kärcher Home & Garden app can be downloaded here:

---

• ^™ and ^™ are trademarks or registered trademarks of Google Inc.

• ^® and ^® are trademarks or registered trademarks of Apple Inc.

The Kärcher Home & Garden App offers the following main functions, among others:

• Cleaning modes recommended by KÄRCHER for different floors that can be transferred to the device

• Ability to set up your own cleaning modes

• Step-by-step instructions for initial startup, commissioning, use and device cleaning

• Tips & tricks

• FAQ with detailed troubleshooting guide

• Notification of system updates and their execution

• Connection to the KÄRCHER Service Center

• Usage statistics

• Device settings e.g. Boost time

• Reminder to change rollers

• Connection to the Kärcher online shop, e.g. for purchasing additional accessories

Connecting the device to the Kärcher Home & Garden app:

1. Load the Kärcher Home & Garden app from the Apple App Store or from the Google Play Store.

2. Launch the Kärcher Home & Garden App.

3. Start the Kärcher Home & Garden app with a customer account or as a guest.

4. Add the device and follow the step-by-step instructions.

1. Hold the basic device firmly.

2. Insert the cable into the guide of the plastic connector and fix it in place.

3. Insert the handle bar into the basic unit as far as it will go, until it audibly clicks into place. The handle bar must sit firmly in the device.

   ---

   

4. Place the device on the parking station and let it click into place.

5. Place the device with the parking station on the cleaning station.

   ---

   

6. Rotate the cleaning rollers onto the roller holder until they stop. Pay attention to the colour coding on the inner side of the roller and on the roller holder on the device (e.g. blue to blue).

   ---

   

Note

If desired, a quick start guide can be called up directly on the device. To do this, the device must be switched on.

7. Press the ON / OFF button.

   ---

   

   The device switches on.

   The LCD display asks whether the quick start guide should be called up.

   ---

   

1. Plug the charging cable of the charger into the charging socket on the device.

   ---

   

2. Plug the mains plug of the charger into the socket.

   The LCD display shows the current charging state of the battery.

   ---

   

   The battery is fully charged after 4 hours.

3. Unplug the mains plug for the charger from the socket after charging.

   ---

   

4. Pull the charging cable out of the device.

1. Operate the unlocking button for the parking station with your foot and lift the device.

   ---

   

2. Place the device in the middle of the waste water tank so that it is positioned between the rollers, and then audibly clicks into place. The position of the tank is not important here, as it can be used in both longitudinal directions in the device.

   ---

   

   The waste water tank must sit firmly in the device.

1. Grasp the fresh water tank by the recessed grips at the side and remove it from the device.

2. Open the tank cap and turn it to the side.

   ---

   

3. Fill the fresh water tank with cold or lukewarm tap water up to the MAX marking.

4. If necessary, add KÄRCHER detergent or care agent to the fresh water tank.

   ATTENTION

   Overdosing or underdosing of the detergent or care agent

   Can result in poor cleaning results.

   Follow the dosage recommendations for the detergent or care agent.

5. Close the tank cap.

6. Insert the fresh water tank into the device.

   ---

   

   The fresh water tank must sit firmly in the device.

---

---

• Floor cleaning is performed using a to and fro movement at the same speed as when vacuuming.

• Activate the boost function for heavy soiling. To do this, select the "Cleaning" tab in the main menu and press Right selection button repeatedly until the Boost function is selected. The Boost function is activated for 15 seconds by default and can be customised via the app. The device is then automatically in Cleaning mode 2. The Boost function can also be activated directly by permanently pressing Right selection button from Cleaning mode 1. When the boost function is activated, the roller speed and the amount of water are increased. Let the device slide slowly across the floor without exerting pressure on the device.

  ---

  

• The color of the rollers shows which application they are especially suitable for.

  • Yellow universal rollers: versatile use

  • Rollers with black stripes: Cleaning of insensitive hard floors (e.g. stone, ceramics); not suitable for sensitive natural stone floors (e.g. marble, terracotta)

    Note

    For optimal cleaning results, wash the rollers in the washing machine at 60°C before using them for the first time.

  ATTENTION

  Material damage due to loose rollers

  This may damage the washing machine.

  Place the rollers in a laundry net and load the washing machine with extra laundry.

If a firmware update needs to be carried out, a notification is displayed in the app. The procedure for carrying out the updates is described in the app.

1. Press the ON / OFF button.

   ---

   

   The device switches on.

   A welcome text appears on the LCD display. The "Cleaning" tab is then displayed in the main menu.

2. Moisten the rollers.

   ---

   

   1. Select the "Cleaning" tab. The device starts by moistening the rollers.

   2. Move the device back and forth until the rollers are sufficiently moistened.

   Note

   If the rollers block immediately after switching on, remove the rollers, moisten them under the tap and reinsert them.

3. Activate Cleaning mode 2 if required. Use Right selection button to switch to Cleaning mode 2.

   ---

   

   This increases the roller speed and water quantity.

   The LCD display shows Cleaning mode 2.

   Note

   The setting of Cleaning mode 1 or Cleaning mode 2 depends on the surface to be cleaned (e.g. wood or stone floor).

   The last Cleaning mode setting is always activated when cleaning is started.

4. If necessary, activate the Boost function for cleaning stubborn dirt (see General information on operation).

   ---

   

The app can be used to select cleaning modes recommended by KÄRCHER for different floors. The cleaning modes differ in terms of water quantity and roller speed depending on the sensitivity of the floor. Downloading the App is described in the chapter Connecting the hard floor cleaner with Bluetooth and the app.

The following cleaning modes are available for different floor coverings:

• Tiles

• Laminate

• unsealed parquet

• sealed parquet

• PVC

• Linoleum

• Cork

• Marble

• Rubber mount

• Exposed screed

Customised cleaning modes can also be set via the app. Here it is possible to reduce the amount of water and the roller speed in 5 steps.

The battery symbol on the display shows the battery run time. The display of the battery symbol can be changed via the settings. The battery run time can be represented by:

• the filling level of a battery

• a minute display

• a percentage display

Acoustic or optical signals warn of an empty battery:

• An acoustic signal sounds once and a warning appears on the display approx. 5 minutes before the battery is flat.

  ---

  

• An acoustic signal sounds twice and a warning appears on the display approx. 2 minutes before the battery is flat.

• Once the battery is flat, cleaning is stopped. Cleaning cannot be started as long as the battery is flat.

If the waste water tank is full, the warning "Full tank" appears on the LCD display and an acoustic signal sounds.

---

After 60 seconds, an acoustic signal sounds twice and cleaning is stopped.

As long as the waste water tank is full, the warning "Full tank" appears on the LCD display when cleaning is started and cleaning cannot be started.

1. Press the ON / OFF button.

   The device switches off.

2. Press the unlocking button for the waste water tank with your foot and lift the device.

   ---

   

   The waste water tank detaches from the device.

3. To empty the waste water tank, do not use the top cover to transport it, but use both hands horizontally on the narrow sides.

4. Empty the waste water tank through the opening in the cover. In the case of stubborn soiling, remove the cover of the waste water tank, and rinse out the waste water tank with tap water.

5. Insert the waste water tank (see Fitting the waste water tank).

If the fresh water tank is empty, the warning "Empty tank" appears on the LCD display and an acoustic signal sounds. As a reminder, the acoustic signal sounds once a minute.

---

1. Fill the fresh water tank (see Filling the fresh water tank).

1. Press the ON / OFF button.

   The device switches off.

2. Place the device on the parking station.

   ---

   

   Note

   If the device is placed on the parking station without a waste water tank, the unlocking button must be pressed to remove the device.

   ---

   

1. Press the ON / OFF button.

   The device switches off.

2. Place the device on the parking station.

   ---

   

ATTENTION

Adhering dirt deposits

Adhering dirt deposits can damage the device in the long term.

It is recommended to clean the device completely after each application.

3. Clean the device (see Care and service).

1. Place the empty waste water tank in the cleaning station to dry.

   1. Place the device on the parking station and let it click into place.

   2. Then place the device with the parking station on the cleaning station.

      ---

      

2. Mount the cleaned rollers on the device to dry.

   ---

   

3. Charge the battery (see Charging process).

4. Store the device in a dry room.

To be guided through the device cleaning process, you can navigate to the "Device cleaning" tab in the main menu and confirm the display of the instructions. The same steps are explained below. If the instructions are not displayed, the rinsing process starts immediately.

1. Empty and reinsert the waste water tank (see Emptying the waste water tank).

2. Place the device with the empty waste water tank in the cleaning station.

3. Fill the fresh water tank with at least 200 ml of fresh water without a detergent or care agent (see Filling the fresh water tank.

   ---

   

   Note

   It is not necessary to add detergent for the rinsing process.

4. Select the "Device cleaning" tab in the main menu and start the rinsing process using Confirm button.

   ---

   

   A signal tone sounds.

   The rinsing process begins and takes about 2 minutes.

   The time runs down on the display until self-cleaning is complete.

   ---

   

   Note

   At the start of the rinsing process, the water runs from the fresh water tank onto the rollers for approx. 80 seconds. During this time the device is silent. Only at the end of the rinsing process do the rollers start to turn for approx. 30 seconds.

5. An acoustic signal sounds when the rinsing process has finished.

6. Press the unlocking button for the waste water tank and place the device on the parking station. The waste water tank remains in the cleaning station.

   Note

   If you try to start cleaning with a full waste water tank, the warning "Tank full" appears on the LCD display and cleaning cannot be started.

7. Push the unlocking button for the hair filters inwards.

   ---

   

   The hair filters are released.

8. Place the hair filters in the cleaning station.

9. Remove the rollers and place them in the cleaning station.

   ---

   

10. Transport the cleaning station with waste water tank, hair filters and rollers to the toilet, sink or trash can as required.

    ---

    

11. Clean the waste water tank (see Cleaning the waste water tank).

12. Clean the rollers (see Cleaning the rollers).

13. Clean the hair filters (see Cleaning the hair filters).

14. Clean the underside of the floor head and the roller drive with a moist cloth.

    ---

    

    Note

    Do not clean the device or the top or bottom of the floor head under running water or under a shower spray, otherwise water may enter.

15. Empty and dry the cleaning station.

16. If there is still water in the fresh water tank, remove the fresh water tank and empty it.

For information on emptying and removing the waste water tank, see Emptying the waste water tank.

1. Remove the cover of the waste water tank.

   ---

   

2. Clean the waste water tank and the cover using tap water.

3. Alternatively, the waste water tank can be cleaned in the dishwasher.

   Note

   The rubber coating of the waste water tank flap can become sticky after cleaning in the dishwasher. The tightness is not impaired.

1. Press the ON / OFF button.

   The device switches off.

2. Place the device on the parking station.

   ---

   

3. Unscrew the cleaning rollers on the recessed grip.

   ---

   

4. Clean the cleaning rollers under running water or wash them in a washing machine at max. 60 °C.

   ---

   

5. Rotate the cleaning rollers onto the roller holder until they stop. Pay attention to the colour coding on the inner side of the roller and on the roller holder on the device (e.g. blue to blue).

   ---

   

6. Let the rollers on the device and on the parking station dry.

1. Press the ON / OFF button.

   The device switches off.

2. Place the device on the parking station.

   ---

   

3. Push the unlocking button for the hair filters inwards.

   ---

   

   The hair filters are released and can be removed.

4. Clean both hair filters under running water.

5. Remove stuck dirt, e.gin the filter comb, with the cleaning brush.

   ---

   

   ---

   

6. Insert the hair filters into the floor head and allow them to latch into place. Both hair filters must be firmly seated in the device.

   ---

   

• Observe the manufacturer's dosing quantity recommendations when dosing with detergent or care agents.

• To prevent foaming, fill the fresh water tank with water first and the add the detergent or care agent.

• To prevent the tank from overflowing, be sure to leave enough space for the detergent or care agent when filling with water.

• Insert the screwdriver at a 90° angle into the small opening on the back of the handle, and remove the handle.

  ---

  

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

• The "BLE warning" warning appears 

• The warning "full tank" appears even though the waste water tank is either empty or not full 

• The warning "empty tank" appears even though the fresh water tank is full 

• The device is not charging and the error message "charging error" appears 

• The error message "overheating" appears 

• The error message "undercooling" appears 

• Rollers do not rotate and error message "motor error" appears 

• Rollers do not rotate and error message "battery error" appears 

• Rollers do not rotate and error message "system error" appears 

• Rollers do not rotate and error message "blocked rollers" appears 

• Rollers do not rotate and error message "BMS error" appears 

• Rollers do not rotate and error message "memory error" appears 

• Rollers do not rotate and error message "watchdog error" appears 

• The battery is not being charged 

• The device cannot be switched on 

• The cleaning and device cleaning functions are greyed out on the LCD display and cannot be started 

• The device rattles loudly when switched on 

• The device does not pick up the dirt 

• The rollers are too dry 

• Poor cleaning result 

• The water absorption is not optimal 

• The device is losing waste water 

• The device switches itself off 

• The device hooks into joints during use 

• The device cannot be connected to the app 

• Transfer of cleaning modes from the app to the device does not work 

• The device cannot be registered in the app 

Cause:

The device cannot be connected to the smartphone via Bluetooth.

Remedy:

1. Contact the authorized Customer Service.

   This error does not affect cleaning with the device.

Cause:

If detergents from other manufacturers are used or if too much detergent is used, a lot of foam may form in the waste water tank, causing the volume of 200 ml in the waste water tank to be reached and cleaning to stop.

Remedy:

1. Use only KÄRCHER detergents and ensure the correct dosage.

Cause:

The contacts for detecting the filling level are dirty.

Remedy:

1. Clean the contacts for detecting the filling level with a damp cloth.

2. If the error message continues to appear, contact authorised Customer Service.

Cause:

The sensor in the fresh water tank holder is dirty.

Remedy:

1. Remove the fresh water tank and clean the sensor (see Description of the device) of the fresh water tank holder, e.g. with a cotton swab.

Cause:

The water filled in is too soft.

Remedy:

1. Do not use distilled water for cleaning.

Cause:

An incorrect or defective charger is being used.

Remedy:

1. Use the original charger.

2. Replace the defective charger.

Cause:

The device overheats during operation (e.g.at high ambient temperatures, when used with dry rollers or when used on carpet) or while charging.

Remedy:

1. Allow the device to cool off for approx. 2.5 hours.

   The device can only be switched on or charged again when it has cooled down accordingly.

Cause:

The hard floor cleaner is undercooled.

Remedy:

1. Allow the device to warm up at room temperature.

   The device can only be switched on or charged again when it has warmed up accordingly.

Cause:

The motor is too hot and is no longer supplied with power.

Remedy:

1. Interrupt operation and allow the device to cool down.

Cause:

The motor is defective.

Remedy:

1. Contact the authorized Customer Service.

Cause:

The battery is in an unauthorised condition.

Remedy:

1. Switch the device off and on.

2. Contact the authorized Customer Service.

Cause:

The device is no longer functional. There are many causes for this, e.g.a cable could be damaged.

Remedy:

1. Contact the authorized Customer Service.

Cause:

The device has a motor blockage, e.g.due to excessive pressure on the rollers or through movement into a wall/corner.

Remedy:

1. Switch the device off and on.

Cause:

The rollers are blocked.

Remedy:

1. Remove the rollers and check whether an object has jammed in the rollers.

2. Check whether the rollers are screwed into the roller holder as far as they will go.

3. Check whether dirt has accumulated in the hair filters in the floor head and remove it.

4. Check that the hair filters are inserted correctly. To do this, remove the hair filters and insert them again.

Cause:

The hair filters block the rollers. The rollers are not sufficiently moistened.

Remedy:

1. Press the ON / OFF button.

   The device switches off.

2. Push the unlocking button for the hair filters inwards and remove the hair filters.

3. Press the ON / OFF button.

   The device switches on.

4. Moisten the rollers.

   1. Activate Boost mode, see General information on operation.

   2. Move the device back and forth until the rollers are sufficiently moistened.

   Note

   If the rollers are not sufficiently moistened, remove the rollers, moisten them under the tap and reinsert them.

5. Insert the hair filters.

Cause:

The battery management system has recognised an error.

Remedy:

1. Restart the device.

2. If the error message continues to appear, contact authorised Customer Service.

Cause:

An error occurred during the update

Remedy:

1. Start the update again.

2. If the error message continues to appear, contact authorised Customer Service.

Cause:

There is a software error.

Remedy:

1. Restart the device.

2. If the error message continues to appear, contact authorised Customer Service.

Cause:

The charging plug / mains plug is not connected correctly.

Remedy:

1. Connect the charging plug / mains plug correctly.

Cause:

The battery is empty.

Remedy:

1. Charge the battery.

Cause:

The charging cable is still in the device.

Remedy:

1. Remove the charging cable, as the cleaning and device cleaning functions are not available when the charging cable is plugged in.

Cause:

The rollers are not sufficiently moistened.

Remedy:

1. Moisten the rollers.

   1. Activate the Boost mode, see General information on operation.

   2. Move the device back and forth until the rollers are sufficiently moistened.

   Note

   If the rollers are not sufficiently moistened, remove the rollers, moisten them under the tap and reinsert them.

Cause:

The rollers have deformed.

Remedy:

1. Only store the device on the parking station and not on the floor, as the rollers may deform due to the contact pressure.

Cause:

The fresh water tank is not sitting properly in the device.

Remedy:

1. Insert the fresh water tank so that it is firmly seated in the device.

Cause:

The waste water tank is missing or not properly seated in the device.

Remedy:

1. Insert the waste water tank in the device so that it audibly latches into place.

2. Check whether the cover of the waste water tank is put on correctly (filler tab must be placed in the recess provided).

Cause:

The hair filters are missing or not properly seated in the device.

Remedy:

1. Insert the hair filters correctly into the device.

Cause:

The rollers are missing or not properly seated in the device.

Remedy:

1. Insert the rollers or turn the rollers onto the roller holder as far as possible.

Cause:

The rollers are dirty or worn out.

Remedy:

1. Clean or replace the rollers.

Cause:

The rollers are not sufficiently moistened.

Remedy:

1. Moisten the rollers.

   1. Activate the Boost mode, see General information on operation.

   2. Move the device back and forth until the rollers are sufficiently moistened.

   Note

   If the rollers are not sufficiently moistened, remove the rollers, moisten them under the tap and reinsert them.

Cause:

The fresh water filter is dirty.

Remedy:

1. Clean the fresh water filter.

   1. Remove the fresh water tank and take out the fresh water filter (see Description of the device).

   2. Clean the fresh water filter under running water.

   3. Insert the fresh water filter again.

Cause:

The rollers are not sufficiently moistened.

Remedy:

1. Moisten the rollers.

   1. Activate the Boost mode, see General information on operation.

   2. Move the device back and forth until the rollers are sufficiently moistened.

   Note

   If the rollers are not sufficiently moistened, remove the rollers, moisten them under the tap and reinsert them.

Cause:

The fresh water filter is dirty.

Remedy:

1. Clean the fresh water filter.

   1. Remove the fresh water tank and take out the fresh water filter (see Description of the device).

   2. Clean the fresh water filter under running water.

   3. Insert the fresh water filter again.

Cause:

The fresh water nozzles on the floor head are blocked.

Remedy:

1. Clean the nozzles on the underside of the floor head with a cloth or soft brush.

2. If the problem persists, contact authorised customer service.

Cause:

Rollers were not washed before first use.

Remedy:

1. Wash rollers at 60 °C in the washing machine.

Cause:

The rollers are dirty.

Remedy:

1. Clean the rollers.

Cause:

The rollers are not sufficiently moistened.

Remedy:

1. Moisten the rollers.

   1. Activate the Boost mode, see General information on operation.

   2. Move the device back and forth until the rollers are sufficiently moistened.

Cause:

The wrong detergent or dosage used.

Remedy:

1. Use only KÄRCHER detergents and ensure the correct dosage.

Cause:

There are residues of foreign detergents on the floor.

Remedy:

1. Thoroughly remove detergent residues from the rollers with water.

2. Clean the floor several times using the device and clean rollers, without using detergent.

   This removes all detergent residues from the floor.

Cause:

The device's hoses are dirty.

Remedy:

1. Start the rinsing process, see Floor head cleaning by means of rinsing process.

Cause:

The hair filters are dirty.

Remedy:

1. Clean the hair filters, see Cleaning the hair filters.

Cause:

The hair filters are not seated properly in the device.

Remedy:

1. Insert the hair filters correctly into the device.

Cause:

The rollers are worn out.

Remedy:

1. Replace the rollers.

Cause:

The waste water tank is full.

Remedy:

1. Empty the waste water tank immediately.

Cause:

The waste water tank is not seated properly in the device.

Remedy:

1. Insert the waste water tank in the device so that it audibly latches into place. The waste water tank must sit firmly in the device.

Cause:

The hair filters are not seated properly in the device.

Remedy:

1. Check that the hair filters are inserted correctly.

Cause:

The waste water tank is damaged.

Remedy:

1. Contact the authorized Customer Service.

Cause:

The automatic device shutdown is activated when the waste water tank has exceeded a volume of 200 ml.

The use of detergents from other manufacturers can lead to excessive foam formation and the device shutdown is activated before 200 ml is reached.

Remedy:

1. Empty the waste water tank.

2. Use only KÄRCHER detergents and ensure the correct dosage.

Cause:

The knobs on the underside of the waste water tank are damaged or worn.

Remedy:

1. Contact the authorized Customer Service.

Cause:

Bluetooth is switched off on one of the two devices.

Remedy:

1. Switch on Bluetooth on both devices.

Cause:

The distance between the smartphone and the device is too great.

Remedy:

1. Make sure that the distance between the device and the smartphone is no more than 10 metres.

Cause:

The pairing process was performed in the wrong order.

Remedy:

1. Start the pairing process on the device first and then in the app. The pairing menu can be found in the device settings.

Cause:

The device and the app are not connected via Bluetooth.

Remedy:

1. Check if the device and the app are connected via Bluetooth. The connection can be established via the FC 8 device card in the app.

Cause:

The part or serial number was not entered correctly during manual registration.

Remedy:

1. Check the part and serial number entered. Both numbers are located on the underside of the floor head.

Cause:

The cloud registration service is currently not available.

Remedy:

1. Try registering again at a later time.

Cause:

The serial number could not be verified.

Remedy:

1. Contact the authorized Customer Service.

Alfred Kärcher GmbH & Co. KG hereby declares that the radio device type Floor Cleaner complies with the 2014/53/EU directive. The full text of the EU Declaration of Conformity can be found at www.karcher.com/fc8.