Read these original instructions and the enclosed safety instructions before using the device for the first time. Act in accordance with them.

Keep both books for future reference or for future owners.

• If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.

• Notify the dealer immediately in the case of shipping damage.

• Check the package contents when unpacking for missing accessories or for damage. Scope of delivery see illustration A.

• At operating elevations of approx. 800 m above sea level or higher, please contact your dealer to have the burner setting adjusted to the elevation and reduced oxygen content.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

Please do not allow engine oil, heating oil, diesel and petrol to enter the environment. Please protect the ground and dispose of old oil in an environmentally friendly manner.

• Control elements for the cleaning process are yellow.

• Control elements for maintenance and servicing are light grey.

Only use the device for cleaning, e.g. machines, vehicles, buildings, tools, façades, terraces and garden equipment.

The following limit values apply to the water supply:

• pH value: 6.5-9.5

• Electrical conductivity: Conductivity of fresh water + 1200 µS/cm, maximum conductivity 2000 µS/cm

• Settleable particles (sample volume 1 l, settling time 30 minutes): < 0.5 mg/l

• Filterable particles: < 50 mg/l, no abrasive substances

• Hydrocarbons: < 20 mg/l

• Chloride: < 300 mg/l

• Sulphate: < 240 mg/l

• Calcium: < 200 mg/l

• Total hardness: < 28 °dH, < 50° TH, < 500 ppm (mg CaCO₃/l)

• Iron: < 0.5 mg/l

• Manganese: < 0.05 mg/l

• Copper: < 2 mg/l

• Active chloride: < 0.3 mg/l

• Free of unpleasant odours

The following safety instructions apply to the device:

• Observe the respectively applicable national regulations for liquid jet cleaners.

• Observe the respectively applicable national accident prevention regulations. Liquid jet cleaners must be tested regularly and the results of the test recorded in writing.

• Note that the heating system in the device is classified as a furnace. Furnaces must be inspected regularly according to the applicable national regulations.

• According to the application national regulations, this device must be initially commissioned by a qualified person when used commercially. KÄRCHER has already performed and documented this initial commissioning for you. You can request the documentation for this from your KÄRCHER partner. Please provide the part number and works number of the device when requesting documentation.

• We explicitly state that the application national regulations require that this device must be inspected regularly by a qualified person. Please contact your KÄRCHER partner for this.

• No modifications may be made to the device or accessories.

Safety devices protect the user and may not be disabled or functionally circumvented.

• When reducing the water volume at the pump head or with the pressure/quantity regulator on the high-pressure gun, the overflow valve opens and part of the water flows back to the pump suction side.

• If the high-pressure gun is closed so that all the water flows back to the pump suction side, the pressure switch on the overflow valve switches off the pump.

• If the high-pressure gun is opened again, the pressure switch on the cylinder head switches the pump on again.

• The overflow valve is set and sealed at the factory. The adjustment is performed only by customer service.

• The safety valve opens if the overflow valve or pressure switch is faulty.

• The safety valve is adjusted and sealed at the factory. The adjustment is performed only by customer service.

The water shortage safeguard prevents the burner from switching on when there is a lack of water.

The exhaust gas thermostat switches the device off when the emission temperature is too high.

1. Apply the parking brake.

1. Mount the handlebar, observing the tightening torque of the screws (6.5-7.0 Nm).

   ---

   

1. Fasten the hubcaps.

   ---

   

1. Fold the lid of the storage compartment vertically upwards and remove it.

   ---

   

2. Fold out the folding compartment.

3. Unlock the storage compartment from below using the 2 latches and pull it out upwards.

   ---

   

4. Close the folding compartment.

5. Insert the hose reel into the two guide rails, let it slide down slowly and lock into place.

   ---

   

6. Fit the hose reel connection hose to the high-pressure connection of the device.

Device with ANTI!Twist: Attach the yellow high-pressure hose connection to the high-pressure gun.

1. Connect the spray lance to the high-pressure gun and hand-tighten (EASY!Lock).

   ---

   

2. Plug the high-pressure nozzle onto the spray lance.

3. Fit the union nut and hand-tighten (EASY!Lock).

4. Device without a hose reel: Connect the high-pressure hose to the high-pressure gun and high-pressure connection of the device and tighten hand-tight (EASY!Lock).

5. Device with a hose reel: Connect the high-pressure hose to the high-pressure gun and hand-tighten (EASY!Lock).

   ATTENTION

   Rolled-up high-pressure hose

   Risk of damage

   Fully unroll the high-pressure hose before starting operation.

1. Determine the local water hardness via the local supply company or with a hardness tester (order number 6.768-004.0).

• System care is a highly effective agent for preventing calcification of the pump when operating with calcareous tap water. This is drip-fed dosed into the float tank.

• The dosage is set to medium water hardness at the factory.

1. Fill up the system care.

1. Open the tank cap.

2. Refill the fuel.

3. Close the tank cap.

4. Wipe up the spilt fuel.

1. Fill with detergent.

• See the "Technical data" for the connected loads.

1. Connect the supply hose (minimum length 7.5 m, minimum diameter 3/4") to the water connection of the device and to the water inlet (e.g. tap) using the water connection adapter.

2. Open the water inlet.

If the device is to draw water from an external container, the following modification is required:

1. Open the filling hole for system care.

   ---

   

2. Unscrew and remove the system care cover.

3. Remove the water connection on the fine filter.

4. Unscrew the fine filter on the pump head.

5. Remove the system care container.

   ---

   

6. Unscrew the upper supply hose to the float tank.

7. Connect the upper supply hose to the pump head.

   ---

   

8. Plug the flushing line of the detergent dosing valve onto the blind plug.

9. Connect the suction hose (diameter at least 3/4") with filter (accessory) to the water connection.

10. Hang the suction hose in an external water source.

    Note

    Maximum suction height: 0.5 m

11. Until the pump draws in water: Set the pressure/quantity regulator of the pump unit to the maximum value and close the detergent dosing valve.

12. Reinstall in the in the reverse order. Make sure that the solenoid valve cable is not pinched on the system care container.

• For connected loads, see technical data and type plate.

• The electrical connection must be carried out by an electrician and comply with IEC 60364-1.

1. Opening the high-pressure gun: Actuate the safety lever and trigger.

2. Closing the high-pressure gun: Release the safety lever and trigger.

1. Switch off the device and operate the high-pressure gun until the device is depressurized.

2. Lock the high-pressure gun by pushing the safety latch forwards.

3. Change the nozzle.

1. Set the trigger to the operating mode. The standby mode indicator light lights up. The device starts up briefly and switches off as soon as the working pressure is reached.

   Note

   If the direction of rotation indicator light lights up during operation, switch off the device immediately and rectify the fault, see "Troubleshooting".

2. Unlock the high-pressure gun by pushing the safety latch to the rear. When the high-pressure gun is actuated, the device switches on again.

   Note

   If no water comes out of the high-pressure nozzle, bleed the pump. See help in the event of malfunctions – device does not build up pressure.

• 30 °C to 98 °C: Clean with hot water.

• 100 °C to 150 °C: Clean with steam.

1. Set the power switch to the desired temperature.

2. During steam operation: Replace the high-pressure nozzle (stainless steel) with the steam nozzle (brass) (see Operation with steam).

1. Turn the regulating spindle clockwise: Increase the working pressure (MAX).

2. Turn the regulating spindle anticlockwise: Reduce the working pressure (MIN).

1. Set the power switch to max. 98 °C.

2. Set the working pressure on the pressure/quantity regulator of the pump unit to the maximum value.

3. Adjust the working pressure and flow rate by turning (variable) the pressure/quantity regulator on the high-pressure gun (+/-).

• Use detergents sparingly to conserve the environment.

• The detergent must be suitable for the surface to be cleaned.

1. Set the concentration of the detergent via the detergent dosing valve according to the manufacturer's instructions.

1. Set the working pressure, the cleaning temperature and the detergent concentration according to the surface to be cleaned.

1. Loosen dirt: Spray the detergent sparingly and let it take effect for 1... 5 minutes, but do not let it dry.

2. Remove dirt: Rinse off the loosened dirt with the high-pressure jet.

For removing light contamination and for rinsing, e.g. garden machines, terrace, tools.

1. Adjust the working pressure as required.

The device works in the most economical temperature range (max. 60 °C).

• 30-50 °C: Light soiling

• Max. 60 °C: Soiling containing protein, e.g. in the food industry

• 60-90 °C: Car cleaning, machine cleaning

• 100-110 °C: Preservative removal, very greasy soiling

• Up to 140 °C: Thawing aggregates, façade cleaning in some cases

1. Set the power switch to the desired temperature.

It is therefore essential that the following measures are carried out:

1. Replace the high-pressure nozzle (stainless steel) with the steam nozzle (brass, part no. see Technical Data).

2. Completely open the pressure/quantity regulator on the high-pressure gun, towards + as far as it will go.

3. Set the working pressure on the pressure/quantity regulator of the pump unit to the minimum value.

4. Set the power switch to min. 100 °C.

1. Lock the high-pressure gun by pushing the safety latch forwards.

1. Set the detergent dosing valve to "0".

2. Set the power switch to level 1 (operation with cold water).

3. Flush the device clean for at least 1 minute with the high-pressure gun open.

1. Close the water inlet.

2. Open the high-pressure gun.

3. Switch on the pump with the power switch and let it run for 5-10 seconds.

4. Close the high-pressure gun.

5. Set the power switch to "0".

6. Only pull the mains plug out of the socket only when your hands are dry.

7. Remove the water connection.

8. Actuate the high-pressure gun until the device is completely depressurised.

9. Lock the high-pressure gun by pushing the safety latch forwards.

1. Snap the spray lance into the holder on the device cover.

2. Roll up the high-pressure hose and the electrical line and hang them on the supports.

3. Device with a hose reel: Stretch out the high-pressure hose before winding it up.

4. Device with a hose reel: Unlock the hose reel by pulling on the high-pressure hose and let the high-pressure hose slowly roll up. Control the reeling speed by holding the hose.

In the case of devices that are connected to a chimney, the ingress of cold air must be taken into account.

1. Shut down the device if frost-free storage is not possible.

For longer breaks in operation or when frost-free storage is not possible:

1. Drain the detergent tank.

2. Drain the water.

3. Flush the device with antifreeze.

1. Unscrew the water supply hose and the high-pressure hose.

2. Unscrew the supply line at the boiler base and allow the heating coil to drain.

3. Allow the device for run for a maximum of 1 minute until the pump and lines are empty.

1. Pour a commercially available antifreeze into the float tank.

2. Switch on the device (without burner) and allow it to run until the device is completely flushed.

This also provides a certain degree of corrosion protection.

---

1. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respectively applicable guidelines.

1. Close the water inlet.

2. Open the high-pressure gun.

3. Switch on the pump with the power switch and let it run for 5-10 seconds.

4. Close the high-pressure gun.

5. Set the power switch to "0".

6. Only pull the mains plug out of the socket only when your hands are dry.

7. Remove the water connection.

8. Actuate the high-pressure gun until the device is completely depressurised.

9. Lock the high-pressure gun by pushing the safety latch forwards.

10. Allow the device to cool down.

You can agree on regular safety inspections or close a maintenance contract with your dealer. Please seek advice on this.

1. Clean the sieve in the water connection.

2. Clean the fine filter.

3. Clean the fuel strainer.

4. Check the oil level.

1. Clean the filter on the detergent suction hose.

1. Change the oil.

2. Have the device maintained by Customer Service.

1. Perform a pressure test according to the manufacturer's specifications.

1. Lift off the cover on the hose reel with a flat head screwdriver.

   ---

   

2. Completely unroll the high-pressure hose from the hose reel.

3. Insert a 10 mm Allen key through the hexagonal opening in the casing. Insert the key until the hose reel is blocked.

   ---

   

   ---

   

4. Unscrew the 2 screws.

   ---

   

5. Remove the hose stopper from the high-pressure hose.

6. Pull out the locking hook.

   ---

   

7. Pull the high-pressure hose out of the hose connection.

8. Insert the new high-pressure hose through the hose guide rollers and insert it into the hose connection. Observe the direction of rotation of the hose reel.

9. Insert the locking hook into the hose connection.

   ---

   

10. Check that all washers are behind the locking hook.

11. Fit the hose stopper to the other end of the high-pressure hose. Distance to the end of the hose about 1 m (to the high-pressure gun).

12. Connect the device to the water supply and power supply, put it into operation and check the connection for leaks.

13. Tension the hose and keep it tensioned. Pull out the Allen key while the hose is taut.

14. Unlock the hose reel by pulling on the high-pressure hose and let the high-pressure hose slowly roll up. Control the reeling speed by holding the hose.

15. Replace the cover.

1. Remove the sieve.

2. Clean the sieve in water.

3. Install the sieve again.

1. Depressurise the device.

2. Unscrew the fine filter on the pump head.

3. Dismantle the fine filter and take out the filter inlay.

4. Clean the filter inlay with clean water or compressed air.

5. Assemble in the reverse order.

1. Knock out the fuel sieve. Do not allow fuel to enter the environment.

1. Pull out the detergent suction hose port.

2. Clean the filter in water.

3. Fit the filter again.

See the "Technical data" section for the oil filling quantity and type.

1. Provide a catch pan for approx. 1 litre of oil.

2. Lever out the retaining clip with a flat head screwdriver and pull out the oil drain plug.

3. Drain the oil into the catch pan.

   Note

   Dispose of the old oil in an environmentally friendly manner or hand it over to an authorised collection point.

4. Push the oil drain plug back in and secure it with the retaining clip.

5. Slowly fill with new oil until the "MAX" marking on the oil tank. The air bubbles must be able to escape.

• The rotation direction indicator light lights up 

• The standby mode indicator light goes out or the device does not run 

• Service indicator light flashes 1x 

• Service indicator light flashes 2x 

• The service indicator light flashes 3x 

• The service indicator light flashes 4x 

• Service indicator light flashes 5x 

• The service indicator light flashes 6x 

• The fuel indicator light lights up 

• System care indicator light lights up 

• Device not building up pressure 

• Device is leaking, water is dripping from the bottom of the device 

• The device switches on and off continuously when the high-pressure gun is locked 

• The device does not suck in any detergent 

• Burner not igniting 

• The set temperature is not reached when operating with hot water 

Remedy:

1. Swap the pins on the power plug.

   ---

   

Cause:

No mains voltage

Remedy:

1. Check the power supply and the supply line.

Cause:

Water shortage

Remedy:

1. Check the water connection and the supply lines.

Cause:

Leak in the high-pressure system

Remedy:

1. Check the high-pressure system and the connections for leaks.

Cause:

Fault in the voltage supply or current consumption of the motor too high

Remedy:

1. Check the power supply and the mains power supply circuit breaker.

2. Contact Customer Service.

Cause:

Motor overloaded/overheated

Remedy:

1. Set the power switch to "0".

2. Allow the device to cool down.

3. Switch the device on.

Cause:

Malfunction occurs repeatedly

Remedy:

1. Contact Customer Service.

Cause:

Exhaust gas thermostat has triggered

Remedy:

1. Set the power switch to "0".

2. Allow the device to cool down.

3. Switch the device on.

Cause:

Malfunction occurs repeatedly

Remedy:

1. Contact Customer Service.

Cause:

Reed switch stuck in the water shortage safeguard or magnetic piston stuck

Remedy:

1. Contact Customer Service.

Cause:

Flame sensor has switched off the burner

Remedy:

1. Contact Customer Service.

Cause:

Fuel tank is empty

Remedy:

1. Refill the fuel.

Cause:

System care container is empty

Remedy:

1. Fill up the system care.

Cause:

Air in the system

Remedy:

1. Venting the pump:

   1. Set the detergent dosing valve to "0".

   2. With the high-pressure gun open, switch the device on and off several times via the power switch.

   3. Open and close the pressure/quantity regulator of the pump unit with the high-pressure gun open.

      Note

      The venting process is accelerated by removing the high-pressure hose from the high-pressure connection.

2. Top up the detergent if necessary.

3. Check connections and lines.

Cause:

Pressure is set to MIN

Remedy:

1. Set the pressure to "MAX".

Cause:

Sieve in the water connection/fine filter is dirty

Remedy:

1. Clean the sieve.

2. Clean the fine filter, replace if necessary.

Cause:

Water supply volume too low

Remedy:

1. Check the water supply volume (see "Technical data").

Cause:

Pump leaking

Remedy:

1. If there is a significant leak, have the device checked by Customer Service.

   Note

   3 drops/minute are permitted.

Cause:

Leak in the high-pressure system

Remedy:

1. Check the high-pressure system and the connections for leaks.

Remedy:

1. Let the device run with the detergent dosing valve open and the water inlet closed until the float tank has been sucked empty and the pressure drops to “0”.

2. Open the water inlet again.

Cause:

If the pump still does not suck in detergent, this can be due to the following reasons:

The filter in the detergent suction hose is dirty

Remedy:

1. Clean the filter.

Cause:

Check valve is stuck

Remedy:

1. Pull off the detergent hose and free up the check valve with a blunt object.

Cause:

Fuel tank is empty

Remedy:

1. Refill the fuel.

Cause:

Water shortage

Remedy:

1. Check the water connection and the supply lines.

Cause:

Fuel filter dirty

Remedy:

1. Change the fuel filter.

Cause:

No ignition spark

Remedy:

1. If no ignition spark is visible through the sight glass during operation, have the device checked by Customer Service.

Cause:

Working pressure/flow rate too high

Remedy:

1. Reduce the working pressure/flow rate via the pressure/quantity regulator of the pump unit.

Cause:

Sooty heating coil

Remedy:

1. Have the soot removed from the device by Customer Service.

If the malfunction cannot be corrected, the device must be checked by the Customer Service department.

• The rotation direction indicator light lights up 

• The standby mode indicator light goes out or the device does not run 

• Service indicator light flashes 1x 

• Service indicator light flashes 2x 

• The service indicator light flashes 3x 

• The service indicator light flashes 4x 

• Service indicator light flashes 5x 

• The service indicator light flashes 6x 

• The fuel indicator light lights up 

• System care indicator light lights up 

• Device not building up pressure 

• Device is leaking, water is dripping from the bottom of the device 

• The device switches on and off continuously when the high-pressure gun is locked 

• The device does not suck in any detergent 

• Burner not igniting 

• The set temperature is not reached when operating with hot water 

Remedy:

1. Swap the pins on the power plug.

   ---

   

Cause:

No mains voltage

Remedy:

1. Check the power supply and the supply line.

Cause:

Water shortage

Remedy:

1. Check the water connection and the supply lines.

Cause:

Leak in the high-pressure system

Remedy:

1. Check the high-pressure system and the connections for leaks.

Cause:

Fault in the voltage supply or current consumption of the motor too high

Remedy:

1. Check the power supply and the mains power supply circuit breaker.

2. Contact Customer Service.

Cause:

Motor overloaded/overheated

Remedy:

1. Set the power switch to "0".

2. Allow the device to cool down.

3. Switch the device on.

Cause:

Malfunction occurs repeatedly

Remedy:

1. Contact Customer Service.

Cause:

Exhaust gas thermostat has triggered

Remedy:

1. Set the power switch to "0".

2. Allow the device to cool down.

3. Switch the device on.

Cause:

Malfunction occurs repeatedly

Remedy:

1. Contact Customer Service.

Cause:

Reed switch stuck in the water shortage safeguard or magnetic piston stuck

Remedy:

1. Contact Customer Service.

Cause:

Flame sensor has switched off the burner

Remedy:

1. Contact Customer Service.

Cause:

Fuel tank is empty

Remedy:

1. Refill the fuel.

Cause:

System care container is empty

Remedy:

1. Fill up the system care.

Cause:

Air in the system

Remedy:

1. Venting the pump:

   1. Set the detergent dosing valve to "0".

   2. With the high-pressure gun open, switch the device on and off several times via the power switch.

   3. Open and close the pressure/quantity regulator of the pump unit with the high-pressure gun open.

      Note

      The venting process is accelerated by removing the high-pressure hose from the high-pressure connection.

2. Top up the detergent if necessary.

3. Check connections and lines.

Cause:

Pressure is set to MIN

Remedy:

1. Set the pressure to "MAX".

Cause:

Sieve in the water connection/fine filter is dirty

Remedy:

1. Clean the sieve.

2. Clean the fine filter, replace if necessary.

Cause:

Water supply volume too low

Remedy:

1. Check the water supply volume (see "Technical data").

Cause:

Pump leaking

Remedy:

1. If there is a significant leak, have the device checked by Customer Service.

   Note

   3 drops/minute are permitted.

Cause:

Leak in the high-pressure system

Remedy:

1. Check the high-pressure system and the connections for leaks.

Remedy:

1. Let the device run with the detergent dosing valve open and the water inlet closed until the float tank has been sucked empty and the pressure drops to “0”.

2. Open the water inlet again.

Cause:

If the pump still does not suck in detergent, this can be due to the following reasons:

The filter in the detergent suction hose is dirty

Remedy:

1. Clean the filter.

Cause:

Check valve is stuck

Remedy:

1. Pull off the detergent hose and free up the check valve with a blunt object.

Cause:

Fuel tank is empty

Remedy:

1. Refill the fuel.

Cause:

Water shortage

Remedy:

1. Check the water connection and the supply lines.

Cause:

Fuel filter dirty

Remedy:

1. Change the fuel filter.

Cause:

No ignition spark

Remedy:

1. If no ignition spark is visible through the sight glass during operation, have the device checked by Customer Service.

Cause:

Working pressure/flow rate too high

Remedy:

1. Reduce the working pressure/flow rate via the pressure/quantity regulator of the pump unit.

Cause:

Sooty heating coil

Remedy:

1. Have the soot removed from the device by Customer Service.

The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

You can find more detailed information at: www.kaercher.com/dealersearch

Only use original accessories and original spare parts. They ensure that the appliance will run safely and fault-free.

Information on accessories and spare parts can be found at www.kaercher.com.

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

Product: High-pressure cleaner

Type: 1.071-xxx

2000/14/EC

2006/42/EC (+2009/127/EC)

2009/125/EC

2011/65/EU

2014/30/EU

2014/53/EU

2014/68/EU

II

Module H

Module H conformity evaluation

Module H conformity evaluation

Conformity evaluation Art. 4 Para. 3

EN IEC 63000: 2018

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60335-1

EN 60335-2-79

EN 61000-3-2: 2014

EN 62233: 2008

HDS 10/21-4, HDS 13/20-4:

EN 61000-3-3: 2013

HDS 9/20-4:

EN 61000-3-11: 2000

(EU) 2019/1781

AD 2000 based on

TRD 801 based on

TÜV Rheinland Industrie Service GmbH

Am Grauen Stein

51105 Köln

ID no. 0035

01 202 111/Q-08 0003

2000/14/EC: Annex V

HDS 9/20-4

Measured: 74

Guaranteed: 93

HDS 10/21-4

Measured: 74

Guaranteed: 93

HDS 13/20-4

Measured: 74

Guaranteed: 93

The signatories act on behalf of and with the authority of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2021/10/01

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

Product: High-pressure cleaner

Type: 1.071-xxx

S.I. 2001/1701 (as amended)

S.I. 2008/1597 (as amended)

S.I. 2010/2617 (as amended)

S.I. 2012/3032 (as amended)

S.I. 2016/1091 (as amended)

S.I. 2017/1206 (as amended)

2014/68/EU

II

Module H

Module H conformity evaluation

Module H conformity evaluation

Conformity evaluation Art. 4 Para. 3

EN IEC 63000: 2018

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60335-1

EN 60335-2-79

EN 61000-3-2: 2014

EN 62233: 2008

HDS 10/21-4, HDS 13/20-4:

EN 61000-3-3: 2013

HDS 9/20-4:

EN 61000-3-11: 2000

(EU) 2019/1781

AD 2000 based on

TRD 801 based on

TÜV Rheinland Industrie Service GmbH

Am Grauen Stein

51105 Köln

ID no. 0035

01 202 111/Q-08 0003

S.I. 2001/1701 (as amended): Schedule 8

HDS 9/20-4

Measured: 74

Guaranteed: 93

HDS 10/21-4

Measured: 74

Guaranteed: 93

HDS 13/20-4

Measured: 74

Guaranteed: 93

The signatories act on behalf of and with the authority of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2021/10/01

• HDS 9/20-4 M/MXA 

• HDS 10/21-4 M/MXA 

• HDS 13/20-4 S/SXA