Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Act in accordance with them.

Keep these original operating instructions for future reference or for future owners.

You will find a QR^® code to call up the online operating instructions in:

---

Trademarks

QR-Code^® is a registered trademark of DENSO WAVE INCORPORATED.

In addition to the notes in the operating instructions, the general safety regulations and accident prevention guidelines applicable by law must be adhered to.

Observe the following warnings when handling the batteries:

	Do not throw / Keep away from fire.
	Do not throw / Keep away from water.

The device consists of two units, a charging station and a battery-powered cleaning robot.

• The device is intended for fully automatic cleaning of textile and hard floor coverings indoors. It can be used for autonomous, continuous maintenance cleaning on all common floor coverings.

• This device has been developed for use in private households and is not intended for the load imposed by commercial use.

The packing materials can be recycled. Do not dispose of packaging as household rubbish but place it in recycling.

Old devices contain valuable, recyclable materials that should be recycled. Batteries and battery packs contain substances which should not be released into the environment. Therefore, please dispose of old devices, batteries and battery packs using suitable collection systems.

Adhere to the recommendations of the legislature regarding the handling of lithium ion batteries. Dispose of used and defective battery packs in accordance with the applicable regulations.

Current information on content materials can be found at: www.kaercher.de/REACH

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

The device consists of a charging station and a battery-powered cleaning robot.

The mobile cleaning robot obtains its energy from a built-in rechargeable battery. The cleaning robot can clean for up to 130 minutes with a single battery charge. It automatically returns to the charging station to recharge when the battery charge decreases.

The cleaning robot moves systematically. It navigates with gyroscope, which enables it to carry out zigzag sweep.

The flat design of the cleaning robot allows it to clean under furniture such as beds, sofas and cupboards.

The cleaning robot has fall sensors that detect stairs and steps and prevent falls, as well as collision sensors that detect and avoid obstacles.

The battery for the cleaning robot is charged in the charging station.

If the cleaning robot starts the cleaning work from the charging station, it returns to the charging station when the battery charge is insufficient.

As soon as the charging process is finished, the cleaning robot automatically leaves the charging station and continues the cleaning work. The cleaning robot also returns to the charging station when it has finished cleaning.

The cleaning robot automatically switches to sleep mode after 5 minutes of inactivity. Press any button to wake it up.

• The cleaning robot does not switch to sleep mode when it is on the charging station.

• The cleaning robot switches off automatically if it is in sleep mode for more than 6 hours

If the cleaning robot encounters an error during operation, the display flashes red and a signal sounds.

For a solution, see chapter (→).

If no action is taken within 5 minutes, the cleaning robot automatically switches to sleep mode.

1. Turn the cleaning robot upside down.

2. Fit the side brush.

   ---

   

Use the following adapter:

• Appliance type: RCV 2

  Power supply:

  Docking Station 9.773-091.0

• Select the location so that the cleaning robot can easily reach the charging station.

• Ensure a distance of at least 0.5 m to the left and right of the charging station and a distance of at least 1.5 m in front of the charging station.

• The location must not be exposed to direct sunlight.

1. Set up the charging station.

   ---

   

2. Plug the mains cable device plug into the cable holder on the side of the charging station.

   ---

   

3. Connect the mains plug.

---

1. Place the cleaning robot on the floor in front of the charging station.

2. Press and hold the on/off switch for 3 seconds.

   The cleaning robot switches on.

3. As soon as the display lights up, place the cleaning robot manually on the charging station and make sure that the charging contacts have a good contact.

After the initial start-up, the cleaning robot automatically moves to the charging station.

The cleaning robot can be controlled directly via buttons on the device, Remote controller or via an App using a WLAN-enabled mobile device.To be able to use all available functions we recommended controlling the cleaning robot via the Kärcher Home Robots App.

Before you download the App, make sure you have the following:

• The mobile device is connected to the Internet.

• The 2.4 GHz WLAN of the router is activated.

• Sufficient WLAN coverage is guaranteed.

Download the Kärcher Home Robots App from the Apple App Store^® or from the ^™ store.

---

---

• ^™ and ^™ are trademarks or registered trademarks of Google Inc.

• ^® and ^® are trademarks or registered trademarks of Apple Inc.

The Kärcher Home Robots App offers the following main functions, among others:

• Setting of time schedules

• Notes on faults or malfunctions and the cleaning progress

• Setting of cleaning preferences (suction modes)

• Activation/deactivation of the "Do not disturb" mode

• FAQ with detailed troubleshooting

• Contact details for the KÄRCHER Service Centres

Connecting the cleaning robot with the Kärcher Home Robots App and WLAN:

1. Download the KÄRCHER Home&Garden App from the Apple App Store or from the Google Play Store.

2. Open the Kärcher Home Robots App.

3. Create an account (if you are not already registered).

4. Add the desired cleaning robot.

5. Follow the step-by-step instructions in the App.

The 2-in-1 dust container with water reservoir may contain a small amount of residual water due to quality control. This is normal.

Use the 2-in-1 dust container with water reservoir when you want to clean both dry and wet.

For dry cleaning, remove the wiper cloth and the wiper cloth holder, see chapter

---

1. Push the 2-in-1 dust container with water reservoir into position until it audibly latches into place.

1. Press the clamp.

2. Remove the 2-in-1 dust container with water reservoir.

   ---

   

1. Attach the wiper cloth to the wiper cloth holder.

   ---

   

   1. Press the wiper cloth onto the wiper cloth holder.

   2. Press on the hook and loop strip.

2. Install the wiper cloth holder.

   ---

   

1. Press any button.

   The cleaning robot stops.

2. Remove the wiper cloth holder.

   ---

   

If you switch to a new router or change your WLAN password, you must reset the cleaning robot's WLAN connection.

1. Switch on the cleaning robot, see chapter

   <fct:ExternalLink>
   
   </fct:ExternalLink>
   .

2. Press the On/Off button and the "Return to charging station" button simultaneously for 7 seconds until a voice says: "Resetting the WLAN connection and entering network configuration mode".

3. Connect the cleaning robot to the charging station, see chapter

   <fct:ExternalLink>
   
   </fct:ExternalLink>
   .

1. Press and hold the "Return to charging station" button for 5 seconds until a signal sounds.

2. Press and hold the "Return to charging station" button again for 5 seconds until a signal sounds.

   Factory settings are restored.

1. Keep the On/Off button pressed when the cleaning robot is in standby and not on the charging station.

   The indicator light flashes while the cleaning robot starts up and then lights up constantly.

   The cleaning robot emits an acoustic signal when the start-up is complete.

2. Place the cleaning robot directly on the charging station.

3. Press the On/Off button.

   In operation, the cleaning robot starts cleaning.

Cleaning modes can only be set up with the App. Downloading the App is described in the chapter

The following cleaning modes are available:

• Dry cleaning

• Combination cleaning

• Wet cleaning

The suction power and water quantity can be set in each of the cleaning modes.

Suction power:

• Quiet

• Standard

• Medium

• Turbo

Water quantity:

• Low

• Medium

• High

1. Keep the On/Off button pressed when the cleaning robot is in standby and not on the charging station.

   The cleaning robot switches off.

1. Press any button during cleaning.

   The cleaning robot stops.

2. Press the On/Off button.

   Cleaning continues.

3. Press the "Return to charging station" button.

   Cleaning is cancelled and the cleaning robot returns to the charging station.

1. If the cleaning robot is moving, press any button.

   The cleaning robot stops.

2. Press the "Return to charging station" button.

   The cleaning robot moves to the charging station for recharging.

The cleaning robot automatically returns to the charging station for recharging when it has completed a cleaning task or when it is low on energy during a cleaning process.

1. Empty the dust container if necessary, see chapter

   <fct:ExternalLink>
   
   </fct:ExternalLink>
   .

2. Insert the dry wiper cloth into the wiper cloth holder, see chapter

   <fct:ExternalLink>
   
   </fct:ExternalLink>
   .

3. Press the On/Off button.

   The cleaning robot starts cleaning.

1. Press any button.

   The cleaning robot stops.

2. Remove the 2-in-1 dust container with water reservoir.

   <fct:ExternalLink>
   
   </fct:ExternalLink>

3. Refill water.

   ---

   

   1. Pull up the rubber tab.

   2. Fill with water.

   3. Press the rubber tab down.

4. Install the 2-in-1 dust container with water reservoir.

5. Dampen the wiper cloth under running water and wring out to remove excess water.

6. Install the wiper cloth, see chapter

   <fct:ExternalLink>
   
   </fct:ExternalLink>
   .

7. Press the On/Off button.

   The cleaning robot starts cleaning.

1. Press any button.

   The cleaning robot stops.

2. Remove the 2-in-1 dust container with water reservoir.

   ---

   

3. Refill water.

   ---

   

   1. Pull up the rubber tab.

   2. Fill with water.

   3. Press the rubber tab down.

4. Install the 2-in-1 dust container with water reservoir.

   ---

   

5. Press the On/Off button.

   Cleaning continues.

1. Press any button.

   The cleaning robot stops.

2. Remove the 2-in-1 dust container with water reservoir.

3. Empty the 2-in-1 dust container with water reservoir.

   ---

   

   1. Open the filter flap.

   2. Empty the 2-in-1 dust container with water reservoir.

   3. Close the filter flap.

4. Install the 2-in-1 dust container with water reservoir.

5. Press the On/Off button.

   Cleaning continues.

The wiper cloth can be cleaned during a cleaning process.

1. Press any button.

   The cleaning robot stops.

2. Remove the wiper cloth holder.

   ---

   

3. Clean the wiper cloth.

4. Install the wiper cloth, see chapter Installing the wiper cloth holder with wiper cloth.

5. Press the On/Off button.

   Cleaning continues.

Where possible, always transport or return the device in the original packaging. Please contact our Service Department if the original packaging is not available.

The lithium-ion battery is subject to the requirements of dangerous goods regulations.

An undamaged and functional battery pack can be transported by the user in public traffic areas without any further restrictions.

When shipping by third parties (transport companies), special requirements for packaging and labelling must be observed.

Observe the national regulations.

1. Clean the cleaning robot, see chapter (→).

2. Fully charge the cleaning robot, see chapter Manually sending the cleaning robot for recharging.

3. Unplug the charger from the mains socket and the station.

4. Switch off the cleaning robot, see chapter Switching off the cleaning robot.

5. Store the cleaning robot in a cool and dry place.

Prior to cleaning and maintaining, power off the device and unplug the power adapter. Any other servicing should be performed by an authorized service representative.For optimal performance, follow the instructions below to clean and maintain Robot regularly. The cleaning and replacement frequency will depend on your Robot usage habits.

1. Press any button to detach the 2-in-1 dust container.

   The cleaning robot stops.

2. Open the lid of the 2-in-1 dust container.

3. Empty the 2-in-1 dust container with water reservoir and shake it to get rid of the remains, see chapter.Emptying the 2-in-1 dust container with water reservoir

   ---

   

4. Take out the filter ,remove the cleaning tool form the 2-in-1 dust container to clean the filter.

   ---

   

5. Reinstall the 2-in-1 dust container onto Robot, see chapter.(→)

1. Turn over the main unit, push the release tabs with both hands to unlock the brush guard, as shown.

   ---

   

2. Take out the rolling brush. Clean the hair entangled on the rolling brush and debris with a scissor or cleaning tool.

   ---

   

3. Use a cleaning tool to brush off the dust in the slot as well.

4. Reinstall the rolling brush by inserting the fixed protruding end first.

   ---

   

Foreign substances, such as hair, can easily get tangled in the side brush, so it is best to clean it regularly.

1. Remove the side brush.

   ---

   

2. Carefully unwind and pull off any hair or substances that are wrapped between the main unit and the side brush.

3. Clean the side brush with water.

   ---

   

To maintain the best performance, clean the sensors and charging pins regularly.

---

1. Dust off the sensors and charging contact pins using a soft fry cloth or cleaning brush.

Clean the fall sensors monthly.

---

1. Wipe the fall sensors with a soft cloth.

We recommend replacing the filter after 3 to 6 months.

1. Press any button.

   The cleaning robot stops.

2. Remove the 2-in-1 dust container with water reservoir, see chapter Removing the 2-in-1 dust container with water reservoir .

3. Remove the filter.

   ---

   

   1. Open the filter flap.

   2. Remove the filter flap.

   3. Remove the filter.

4. Install the new filter.

   ---

   

   1. Fit the filter.

   2. Fit the filter flap.

   3. Close the filter flap.

5. Install the 2-in-1 dust container with water reservoir , see chapter Installing 2-in-1 dust container with water reservoir .

6. Press the On/Off button.

   Cleaning continues.

We recommend replacing the brush after 6 to 12 months.

1. Remove the brush.

   ---

   

   1. Press the clamps together.

   2. Remove the brush cover.

   3. Remove the brush.

   4. Remove the brush bearing.

2. Install the new brush.

   ---

   

   1. Fit the brush bearing.

   2. Fit the brush.

   3. Fit the brush cover and press it down until it audibly latches into place.

We recommend replacing the side brush after 3 to 6 months.

1. Turn the cleaning robot upside down.

2. Remove the side brush.

   ---

   

3. Install the new side brush.

   ---

   

The rechargeable battery has reached the end of its life if the cleaning robot constantly drives to the station for charging after a short cleaning operation.

1. Switch off the cleaning robot, see chapter Switching off the cleaning robot.

2. Send the cleaning robot to the Customer Service. Observe the regulations for shipping lithium-ion batteries, see Chaptertransport.

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

• Battery does not charge 

• The cleaning robot is not returning to the charging station 

• The cleaning robot produces unusual noises 

• The cleaning robot does not continue cleaning 

• The cleaning robot does not start 

• The cleaning robot does not clean efficiently or leaves dust behind 

• The cleaning robot cannot connect to the WLAN/The cleaning robot goes offline 

Cause:

Charging contacts are dirty.

Remedy:

1. Wipe the charging contacts on both the charging station and the cleaning robot with a dry cloth.

Cause:

Ambient temperature below 0 °C or above 35 °C.

Remedy:

1. Use the cleaning robot at temperatures above 0 °C and below 35 °C.

Cause:

Battery is discharged.

Remedy:

1. Manually place the cleaning robot on the charging station and let it charge completely.

Cause:

The cleaning robot is too far away from the charging station.

Remedy:

1. Move the cleaning robot closer to the charging station.

2. Manually place the cleaning robot on the charging station.

Cause:

Not enough space around the charging station.

Remedy:

1. Ensure that there is sufficient space around the charging station, see chapter Setting up the charging station.

Cause:

There are too many obstacles around the charging station.

Remedy:

1. Place the charging station in a more open area, see chapter Setting up the charging station.

Cause:

A foreign object could be caught in the brush, the side brush or in a wheel.

Remedy:

1. Switch off the cleaning robot.

2. Remove any foreign objects.

Cause:

The cleaning robot is in "Do not disturb" mode.

Remedy:

1. Ensure that the cleaning robot is not in "Do not disturb" mode.

Cause:

The cleaning robot is being charged manually or has been placed in the charging station.

Remedy:

1. Wait until the cleaning robot is fully charged.

Cause:

Ambient temperature is below 0 °C or above 35 °C.

Remedy:

1. Use the cleaning robot at temperatures above 0 °C and below 35 °C.

Cause:

Charging state is too low.

Remedy:

1. Charge the cleaning robot.

Cause:

Collision sensor is dirty or too close to the virtual wall.

Remedy:

1. Remove foreign objects by carefully tapping on the collision sensor.

2. Move the cleaning robot to another location and start it.

Cause:

Fall sensors are dirty.

Remedy:

1. Clean the fall sensors with a dry cloth.

Cause:

2-in-1 dust container with water reservoir or dust container is not installed or incorrectly installed.

Remedy:

1. Make sure that the 2-in-1 dust container with water reservoir or the dust container is installed and correctly latched into place, see chapter Installing 2-in-1 dust container with water reservoir.

Cause:

Filter not installed or incorrectly installed.

Remedy:

1. Make sure that the filter is correctly installed.

Cause:

Filters dirty.

Remedy:

1. Clean the filter, see chapter

   <fct:ExternalLink>
   
   </fct:ExternalLink>
   .

2. If the error persists, replace the filter, see chapter

   <fct:ExternalLink>
   
   </fct:ExternalLink>
   .

Cause:

Wiper cloth or wiper cloth holder not or incorrectly installed.

Remedy:

1. Ensure that the wiper cloth holder and wiper cloth are correctly installed, see chapter Installing the wiper cloth holder with wiper cloth.

Cause:

The cleaning robot is jammed or stuck.

Remedy:

1. Remove obstacles.

Cause:

The cleaning robot or one of its wheels has no floor contact.

Remedy:

1. Place the cleaning robot on a flat surface.

Cause:

The 2-in-1 dust container with water reservoir or the dust container is full.

Remedy:

1. Empty the 2-in-1 dust container with water reservoir or the dust container, see chapter Emptying the 2-in-1 dust container with water reservoir.

   <fct:ExternalLink>
   
   </fct:ExternalLink>

Cause:

The filter is clogged.

Remedy:

1. Clean the filter, see chapter

   <fct:ExternalLink>
   
   </fct:ExternalLink>

Cause:

A foreign object has become caught in the brush

Remedy:

1. Clean the brush, see chapter Cleaning the rolling brush.

2. Clean the side brush, see chapter Cleaning the side brush.

Cause:

Bluetooth of the mobile is not opened.

Remedy:

1. Make sure the Bluetooth of the mobile is opened.

Cause:

The cleaning robot is not connected to the network or is not within the range of the WLAN signal.

Remedy:

1. Make sure that the cleaning robot is connected to the network and is within the range of the WLAN signal.

2. Make sure that the WLAN password is correct.

3. Reset the WLAN and connect again (5 GHz WLAN networks are not supported).

Cause:

The WLAN signal is too weak.

Remedy:

1. Make sure that the cleaning robot is within range of the WLAN signal.

The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

You can find more detailed information at: www.kaercher.com/dealersearch

Alfred Kärcher SE & Co. KG hereby declares that the radio device type Robo Cleaner complies with the 2014/53/EU directive. The full text of the EU Declaration of Conformity can be found at www.kaercher.com/RCV 2.

Alfred Kärcher SE & Co. KG hereby declares that the radio device type Robo Cleaner complies with the UK regulation S.I. 2017/1206 (as amended). The full text of the Declaration of Conformity can be found at www.kaercher.com/RCV 2.