Read this safety chapter and these original instructions before using the device for the first time. Act in accordance with them. Keep the original instructions for future reference or for future owners.

• In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.

• Warnings and information notices attached to the device provide important information for hazard-free operation.

Only use the device in private households.

The device is intended for use as a spray extraction cleaner for cleaning car interiors, upholstery textiles and carpets in accordance with the descriptions given in these operating instructions and the safety instructions.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

Our local KÄRCHER branch will be happy to help you if you have any questions or problems with the device.

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

Further information can be found at: www.kaercher.com/dealersearch

Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".

The device is equipped with different equipment depending on the model selected. The specific equipment is described on the device packaging.

---

1. Spray suction hose connection
2. Waste water tank with lid
3. Fresh water tank with lid
4. Holder for spray suction hose handle
5. Tank cap
6. Power switch (I (On) / O (Off))
7. Carrying handle
8. Storage for sponge, brush, detergent bag
9. Holder for mains cable and spray extraction floor nozzle
10. Mains cable
11. Spray suction hose and handle with spray lever and locking button
12. Spray extraction upholstery nozzle
13. Spray extraction crevice nozzle
14. * Spray suction tubes 2 x 0.5 m
15. * Spray extraction floor nozzle
16. Detergent RM 519 (100 ml)

* optional

1. Press the spray suction hose into the suction hose connection on the device until it latches into place.

   • To remove, press the latch and pull the spray suction hose out.

   ---

   

2. Fit the accessory as required. See chapter Installing accessories.

Filling the water reservoir directly on the device

1. Pull the tank cap upwards and turn sideways. Dose the detergent according to the specifications and then fill the tank with tap water up to the "MAX" mark.

   ---

   

2. Close the tank cap.

Removing the water tank for filling

1. Pull out the water tank vertically upwards by the recessed grip.

   ---

   

2. Pull the tank cap upwards, turn it sideways and fill the water tank with detergent and tap water up to the "MAX" mark.

   ---

   

   or

   Unlock the tank lid, remove it and fill with detergent and tap water up to the "MAX" mark.

   ---

   

3. Close the tank cap or fit the tank lid making sure that it is firmly seated.

4. Fit the water tank down to the bottom of the device.

Carpet cleaning

Use the spray suction tube and the spray extraction floor nozzle for carpet cleaning.

1. Plug the spray suction tubes together and the connect to the spray suction hose; all parts must audibly latch into place

2. Push the spray extraction floor nozzle on to the spray suction tube until it audibly clicks into place.

• To separate the spray suction tubes and spray extraction floor nozzle, press the respective unlocking button and pull the parts from each other.

  ---

  

  ---

  

Upholstery cleaning

Use the spray extraction upholstery nozzle, spray extraction crevice nozzle or spray extraction floor nozzle for cleaning as required, e.g. for upholstery and mattresses.

• Push the spray extraction upholstery nozzle, spray extraction crevice nozzle or spray extraction floor nozzle on to the spray suction hose handle until it audibly clicks into place.

• To separate the spray extraction upholstery nozzle, spray extraction crevice nozzle or spray extraction floor nozzle, press the respective unlocking button and pull it off the spray suction hose.

  ---

  

  ---

  

  ---

  

1. Completely remove the power cable from the cable hook.

2. Plug the mains plug into a socket.

   ---

   

3. Turn the power switch to position I (On).

   ---

   

   Start the suction motor and pump.

4. Close the air damper completely.

   ---

   

1. Fill the fresh water tank with detergent and water, see chapterFilling the fresh water tank.

2. Switch on the device, see Chapter Switching on the device

3. Select the accessory as required and press the lever on the handle to spray the cleaning solution.

4. To spray large areas, first press the lever on the handle and then press the locking button.

   ---

   

5. Pull the spray extraction upholstery nozzle or spray extraction floor nozzle backwards over the surface to be cleaned in overlapping paths, do not push.

   ---

   

   Note

   For faster and more effective work, the spray extraction floor nozzle can also be used for cleaning upholstery (e.g. large sofas).

Note

When the wastewater container is full, a float switch closes the suction opening and the device runs at a higher speed.

6. Switch off the device immediately and empty the waste water container, see chapter Emptying the waste water tank.

1. Turn the power switch to position I (On).

   ---

   

   Start the suction motor and pump.

2. Press the lever for spraying.

   Cleaning solution is sprayed.

   ---

   

3. Release the lever for spraying and suck up the cleaning solution residue.

   If necessary, the air leakage slider can be adjusted to regulate the suction power.

   ---

   

4. After cleaning, clean the upholstery and carpet with clear, warm water and impregnate if desired.

1. Turn the power switch to position I (On).

   ---

   

   Start the suction motor and pump.

2. Press the lever for spraying.

   ---

   

   Cleaning solution is sprayed.

3. Turn the power switch to position 0 (Off).

   ---

   

4. Allow the cleaning solution to act for at least 5 minutes.

5. Turn the power switch to position I (On).

   Start the suction motor and pump.

   ---

   

6. Suck off any residues of the cleaning solution.

   If necessary, the air leakage slider can be adjusted to regulate the suction power.

   ---

   

7. Repeat the process if necessary.

8. After cleaning, clean the upholstery and carpet with clear, warm water and impregnate if desired.

1. Turn the power switch to position 0 (Off).

   ---

   

2. Empty the waste water tank, see chapterEmptying the waste water tank.

3. Fill the fresh water tank with tap water up to the "MAX" mark, see chapter Filling the fresh water tank.

4. Connect the spray suction hose to the crevice nozzle.

5. Open the tank cap and insert the crevice nozzle completely into the opening.

6. Turn the power switch to position 1 (On) and simultaneously press and hold down the spray lever on the handle.

   ---

   

   The rinsing process is finished as soon as the fresh water tank is completely empty.

7. Turn the power switch to position 0 (Off).

   ---

   

8. Pull the mains plug out of the outlet. Wrap the mains cable completely but not too tightly (loosely) around the cable holder.

   ---

   

9. Empty the waste water tank, see chapterEmptying the waste water tank.

10. Thoroughly rinse the waste water tank with clear water.

11. If contaminated, also rinse the fresh water tank with clear water and clean the filter, see chapter Cleaning the fresh water tank filter

12. Disconnect the accessories from the device.

13. To remove any remaining liquid in the spray suction hose:

    1. Press the latch and remove the spray suction hose from the device.

       ---

       

    2. Press the lever on the handle and let the liquid flow out.

       Note

       To allow the liquid to dry completely, do not wrap the spray/suction hose around the device to dry.

       Note

       To avoid puddles in the living area (e.g. on carpet, parquet), let the remaining liquid run in a suitable container (e.g. sink, bucket).

14. Rinse the washing nozzles with tap water and let the device dry with the other accessories.

15. Stow the device in the "drying position" (with the two tank lids slightly open so that any remaining liquid can dry without leaving any residue).

1. Pull out the dirty water tank vertically upwards by the recessed grip.

   ---

   

2. Unlock the two side ones tank caps, remove the filler cap and dispose of waste water.

   ---

   

3. When continuing the cleaning work: Replace the filler cap, making sure that it is firmly seated. Insert the waste water tank down to the bottom of the device.

4. At the end of the cleaning work: Stow the device in the "drying position" (the filler cap is slightly open and any remaining liquid can dry without leaving any residue).

1. Attach the spray extraction floor nozzle to the accessory holder on the cable holder.

2. Wrap the spray suction hose around the device.

3. Attach the handle / hose from the spray suction hose to the accessory holder on the side of the device using the rubber band. Pay attention to the correct winding direction so that the handle or hose can be attached with the rubber band.

   ---

   

4. Store the device in a dry and frost-proof room.

1. Lift and carry the device by the carrying handle.

1. Secure the device against slipping and tipping over.

• Clean the device and plastic accessory parts with a commonly available plastic cleaner.

• Rinse the container and accessories with water, as necessary, and dry them before further use.

1. Remove the waste water tank from the device, see chapter Emptying the waste water tank

2. Remove the tank lid from the tank and remove the separator.

3. Carefully clean the tank lid and separator with a damp cloth.

4. Carefully remove moisture with a dry cloth.

   ---

   

5. Fit the tank lid and separator together, fasten on the tank and fit them back into the device.

1. To clean the spray extraction floor nozzle and spray extraction upholstery nozzle, loosen the nozzle holder by turning it and remove it together with the nozzle.

   Note

   Keep the O-ring/sealing ring in a safe place and reinsert it after cleaning.

   ---

   

2. Clean residues in the spray nozzle under running water.

3. Fit the spray nozzle and sealing ring in the nozzle holder and turn to re-fasten.

4. Also clean residues in the spray nozzle of the spray extraction crevice nozzle under running water.

1. Unlock and remove the tank lid, see chapter Filling the fresh water tank

2. Rinse the filter thoroughly with water or clean it carefully with a soft brush.

   ---

   

3. Close the tank lid and make sure that it is firmly seated.

• Poor suction performance 

• No water emitted from the nozzle 

• Spray jet uneven 

• Device gets louder and no longer sucks up waste water 

Cause:

The air damper is open too wide.

Remedy:

• Close the air damper.

Cause:

Accessory, suction hose or suction tubes are clogged.

Remedy:

• Remove the blockage.

Cause:

Grids of the waste water tank lid are contaminated or wet.

Remedy:

• Clean/dry grids.

Cause:

Dirt receptacle not positioned correctly.

Remedy:

• Press the dirt receptacle downwards.

Cause:

Fresh water tank empty

Remedy:

• Fill up the fresh water tank.

Cause:

Fresh water filter contaminated.

Remedy:

• Clean the fresh water filter.

Cause:

Incorrect connection between accessory and spray suction hose.

Remedy:

• Establish the correct connection.

Cause:

Detergent pump defective.

Remedy:

• Request repair by Customer Service.

Cause:

Spray nozzle on the accessory for spray extracting cleaning is soiled.

Remedy:

• Clean the spray nozzle on the respective accessory.

Cause:

Grids of the waste water tank lid are contaminated or wet.

Remedy:

• Clean/dry grids.