T 11/1 ClassicT 11/1 Classic Re!PlastT 11/1 Classic Adv Re!PlastT 11/1 Classic HEPAT 11/1 Classic HEPA Re!Plast
59802580 (09/24)
General notes
Read these original instructions and the enclosed safety instructions before using the device for the first time. Act in accordance with them.
Keep both books for future reference or for future owners.
If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.
Notify the dealer immediately in the case of shipping damage.
Check the package contents when unpacking for missing accessories or for damage.
Environmental protection
The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.
Current information on content materials can be found at: www.kaercher.de/REACH
Intended use
WARNING
Health risk
Inhalation of dusts that are harmful to health
Do not use the device for vacuuming up dusts that are harmful to health.ATTENTION
Damage to the device
Short-circuit due to high levels of humidity
Only use and store the device indoors.This universal vacuum cleaner for carpets is intended for dry cleaning floor and wall surfaces.
This device is suitable for commercial use, e.g. in hotels, schools, hospitals, factories, shops, offices, and rental companies.
Description of the device
- Fleece filter bag
- Suction hose port
- Suction hose
- Type plate
- Mount for accessories
- Carrying handle
- Hose holder
- Cable clips
- Mains cable
- Suction head
- Suction head lock
- Recessed grip
- Steering roller
- Dirt receptacle
- Mount for floor nozzle
- Main switch
- Hard surface/carpet switch
- Floor nozzle
- Suction pipe
- Main filter basket (T 11/1 Classic HEPA)
- Angle piece
- Main filter basket (T 11/1 Classic)
- Adapter plate (only T 11/1 Classic HEPA)
- HEPA filter (T 11/1 Classic HEPA only)
- Motor protection filter
Preparation
Unpack the device and install the accessories.
Initial startup
Check if the main filter basket is inserted in the device.
Operating modes
Operation with the filter bag
Operation without the filter bag
Installing the filter bag
Unlock and remove the suction head.
Remove the main filter basket.
Fit the fleece filter bag.
Insert the main filter basket.
Fit and lock the suction head.
Operation
Switching on the device
Connect the mains plug.
Switch on the device at the main switch.
Cleaning mode
Set the floor nozzle switch to hard surface or carpet.
Perform cleaning.
Switching off the device
Switch off the device at the main switch.
Pull out the mains plug.
Each time after use
Empty the container.
Vacuum off the inside and outside of the device and clean with a moist cloth.
Transport
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transportation.When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respective valid guidelines.
Storage
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.The device may only be operated indoors.
Care and service
DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.Remove the mains plug.Cleaning the main filter basket
ATTENTION
Danger from wet main filter basket
Risk of damage to the device
Never insert the main filter basket when wet.If necessary, clean the main filter basket (washable) under running water.
Replacing the motor protection filter
T 11/1 Classic only:
Unlock and remove the suction head.
Remove the motor protection filter.
Fit the new motor protection filter.
Fit and lock the suction head.
Replacing the HEPA filter
T 11/1 Classic HEPA only:
Unlock and remove the suction head.
Turn the HEPA filter anticlockwise and remove it.
Place the new HEPA filter on the adapter plate and tighten it clockwise as far as it will go.
Fit and lock the suction head.
Replacing the mains cable
Only T 11/1 Classic Adv Re!Plast:
Replace the mains cable.
Troubleshooting guide
DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.Remove the mains plug.The device stops during operation
Cause:
The motor thermo-protector has triggered
Remedy:
Changing the fleece filter bag.
T 11/1 Classic only: Replace the motor protection filter.
T 11/1 Classic HEPA only: Replace the HEPA filter.
Check all parts for clogging.
Allow the engine turbine to cool for approx. 30-40 minutes. Switch on the device.
Suction turbine does not start up
Remedy:
Check the socket and the power supply fuse.
Check the mains cable and the mains plug of the device.
Switch on the device.
Suction power decreases
Remedy:
Remove any blockages from the suction nozzle, suction pipe or suction hose.
Changing the fleece filter bag.
Clean the main filter basket under running water and dry.
Position/lock the suction head correctly.
Replace the defective suction hose.
T 11/1 Classic only: Replace the motor protection filter.
T 11/1 Classic HEPA only: Replace the HEPA filter.
Escaping dust when vacuuming
Remedy:
Changing the fleece filter bag.
Check the fit of the fleece filter bag.
Position/lock the suction head correctly.
Insert the undamaged main filter basket.
Insert the motor protection filter correctly.
T 11/1 Classic HEPA only: Fasten the HEPA filter correctly.
Customer Service department
If the malfunction cannot be corrected, the device must be checked by the Customer Service department.
The device stops during operation
Cause:
The motor thermo-protector has triggered
Remedy:
Changing the fleece filter bag.
T 11/1 Classic only: Replace the motor protection filter.
T 11/1 Classic HEPA only: Replace the HEPA filter.
Check all parts for clogging.
Allow the engine turbine to cool for approx. 30-40 minutes. Switch on the device.
Suction turbine does not start up
Remedy:
Check the socket and the power supply fuse.
Check the mains cable and the mains plug of the device.
Switch on the device.
Suction power decreases
Remedy:
Remove any blockages from the suction nozzle, suction pipe or suction hose.
Changing the fleece filter bag.
Clean the main filter basket under running water and dry.
Position/lock the suction head correctly.
Replace the defective suction hose.
T 11/1 Classic only: Replace the motor protection filter.
T 11/1 Classic HEPA only: Replace the HEPA filter.
Escaping dust when vacuuming
Remedy:
Changing the fleece filter bag.
Check the fit of the fleece filter bag.
Position/lock the suction head correctly.
Insert the undamaged main filter basket.
Insert the motor protection filter correctly.
T 11/1 Classic HEPA only: Fasten the HEPA filter correctly.
Warranty
The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.
Further information can be found at: www.kaercher.com/dealersearch
Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".
Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at www.kaercher.com.
Attachment kit
Description | Order number |
|---|---|
HEPA filter attachment kit for T 11/1 Classic | 2.889-310.0 |
Note
After the HEPA filter has been installed, the instructions for the T 11/1 Classic HEPA in the operating instructions apply.
Declaration of Conformity
EU Declaration of Conformity |
We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.
Product: Dry vacuum cleaner
Type: 1.527-xxx
Currently applicable EU Directives2006/42/EC (+2009/127/EC)
2009/125/EC
2011/65/EU
2014/30/EU
Harmonised standards usedEN IEC 63000: 2018
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 60312-1: 2017
EN 60335-1
EN 60335-2-69
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 62233: 2008
National standards used-
Commission Regulation(s)666/2013
The signatories act on behalf of and with the authority of the company management.
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2020/10/01
Declaration of Conformity (UK) |
We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.
Product: Dry vacuum cleaner
Type: 1.527-xxx
Currently applicable UK RegulationsS.I. 2008/1597 (as amended)
S.I. 2010/2617 (as amended)
S.I. 2012/3032 (as amended)
S.I. 2016/1091 (as amended)
Designated standards usedEN IEC 63000: 2018
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 60312-1: 2017
EN 60335-1
EN 60335-2-69
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 62233: 2008
National standards used-
Commission Regulation(s)(EU) No 666/2013
The signatories act on behalf of and with the authority of the company management.
Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2020/10/01
Technical data
Kärcher T 11/1 Classic/Re!Plast
Electrical connection | |
Mains voltage | 220-240 V |
Phase | 1 ~ |
Power frequency | 50-60 Hz |
Protection class | II  |
Rated power input | 850 W |
Device performance data | |
Tank content | 11 l |
Air quantity (max.) | 40 l/s |
Vacuum (max.) | 23,5 (235) kPa (mbar) |
Dimensions and weights | |
Length x width x height | 375 x 285 x 385 mm |
Typical operating weight | 3,8 kg |
Diameter of the suction hose | 35 mm |
Ambient conditions | |
Ambient temperature (max.) | +40 °C |
Determined values in acc. with EN 60335-2-69 | |
Sound pressure level LpA | 61 dB(A) |
Uncertainty KpA | 2 dB(A) |
Sound power level LwA | 74 dB(A) |
Hand-arm vibration value | <2,5 m/s2 |
Uncertainty K | 0,2 m/s2 |
Mains cable | |
Power cord type | H05VV-F 2x0,75 mm2 |
Part number (EU) | 6.650-621.0 |
Part number (GB) | 6.650-649.0 |
Part number (CH) | 6.650-837.0 |
Cable length | 7,5 m |
Kärcher T 11/1 Classic Adv Re!Plast
Electrical connection | |
Mains voltage | 220-240 V |
Phase | 1 ~ |
Power frequency | 50-60 Hz |
Protection class | II |
Rated power input | 850 W |
Device performance data | |
Tank content | 11 l |
Air quantity (max.) | 40 l/s |
Vacuum (max.) | 23,5 (235) kPa (mbar) |
Dimensions and weights | |
Length x width x height | 375 x 285 x 385 mm |
Typical operating weight | 4,2 kg |
Diameter of the suction hose | 35 mm |
Ambient conditions | |
Ambient temperature (max.) | +40 °C |
Determined values in acc. with EN 60335-2-69 | |
Sound pressure level LpA | 61 dB(A) |
Uncertainty KpA | 2 dB(A) |
Sound power level LwA | 74 dB(A) |
Hand-arm vibration value | <2,5 m/s2 |
Uncertainty K | 0,2 m/s2 |
Mains cable | |
Power cord type | H05VV-F 2x1,0 mm2 |
Part number (EU) | 6.650-622.0 |
Part number (CH) | 6.650-650.0 |
Cable length | 12 m |
Kärcher T 11/1 Classic HEPA/Re!Plast
Electrical connection | |
Mains voltage | 220-240 V |
Phase | 1 ~ |
Power frequency | 50-60 Hz |
Protection class | II |
Rated power input | 850 W |
Device performance data | |
Tank content | 11 l |
Air quantity (max.) | 40 l/s |
Vacuum (max.) | 23,5 (235) kPa (mbar) |
Dimensions and weights | |
Length x width x height | 375 x 285 x 385 mm |
Typical operating weight | 4,2 kg |
Diameter of the suction hose | 35 mm |
Ambient conditions | |
Ambient temperature (max.) | +40 °C |
Determined values in acc. with EN 60335-2-69 | |
Sound pressure level LpA | 61 dB(A) |
Uncertainty KpA | 2 dB(A) |
Sound power level LwA | 74 dB(A) |
Hand-arm vibration value | <2,5 m/s2 |
Uncertainty K | 0,2 m/s2 |
Mains cable | |
Power cord type | H05VV-F 2x0,75 mm2 |
Part number (EU) | 6.650-621.0 |
Part number (GB) | 6.650-649.0 |
Part number (CH) | 6.650-837.0 |
Cable length | 7,5 m |
<BackPage>
</BackPage>
</BackPage>