The device can be controlled by direct operation on the high-pressure gun or via a mobile device equipped with ^® wireless technology. The KÄRCHER Home & Garden app is required for this.

The app also contains:

• Installation and initial startup information

• Information about the areas of application

• Tips & Tricks

• FAQ with detailed troubleshooting

• Connection to the KÄRCHER Service Centre

The app can be downloaded here:

---

Trademarks

• ^®wordmarks and logos are registered trademarks of Bluetooth SIG, Inc. Any use of these trademarks by Alfred Kärcher SE & Co. KG is under license.

• ^™ and ^™ are trademarks or registered trademarks of Google Inc.

• ^® and ^® are trademarks or registered trademarks of Apple Inc.

Read this safety chapter and these original instructions before using the device for the first time. Act in accordance with them. Keep the original instructions for future reference or for future owners.

• In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.

• Warnings and information notices attached to the device provide important information for hazard-free operation.

The power switch prevents unintentional operation of the device.

The lock locks the lever of the high-pressure gun and prevents the device from starting unintentionally.

If the lever of the high-pressure gun is released, the pressure switch turns off the pump and the high-pressure jet stops. The pump switches on again when the lever is pressed.

The motor circuit breaker shuts off the device if power consumption it too high.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Cleaning work producing in oily waste water, e.g. washing engines, washing undercarriages etc., may only be performed at washing stations with an oil separator.

Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil.

Extraction of water from public waterways is not permitted in some countries.

Current information on content materials can be found at: www.kaercher.de/REACH

Use the high-pressure cleaner in private households only.

The high-pressure cleaner is intended for cleaning machines, vehicles, buildings, tools, façades, terraces, garden machines etc. using a high-pressure water jet.

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

The maximum amount of equipment is described in these operating instructions. Depending on the model used, there are differences in the scope of delivery (see packaging).

---

---

1. Stand with carrying handle
2. Water connection with integrated sieve
3. Transport wheel
4. Hose guide
5. Trigger "0/OFF" / "I/ON"
6. Storage for spray lance
7. High-pressure hose
8. *Plug 'n' Clean detergent bottle
9. Storage / parking position for high-pressure gun
10. 3-in-1 multi-jet spray lance with 3 spray types (see also chapter Smart Control System)
11. Smart Control high-pressure gun
12. LCD display (see also chapter LCD display)
13. Battery compartment lock
14. Battery compartment
15. “+/-” buttons for pressure control
16. High-pressure gun lock
17. Button for separating the high-pressure hose from the high-pressure gun
18. High-pressure gun lever
19. Transport handle, telescoping
20. Carrying handle
21. Hose holder
22. High pressure hose reel
23. Crank handle for hose reel
24. Type plate
25. Accessory compartment
26. Hook for net attachment
27. Accessory compartment net
28. Mains connection with mains plug
29. Water connection coupling
30. **Garden hose (fabric reinforced, diameter at least 1/2 inch (13 mm), length at least 7.5 m, with commercially available quick coupling)
31. **KÄRCHER suction hose for water supply from open containers (order no. 2.643-100.0)

* optional, ** additionally required

Fit the supplied loose parts onto the device before starting up the device.

Have the included screws and the appropriate screwdriver ready.

1. Hang the accessory net on the hooks.

   ---

   

1. Insert the high-pressure hose through the hose guide from the rear.

   ---

   

1. Screw the water connection coupling onto the water connection on the device.

   ---

   

Download the app and register your device

1. Download the KÄRCHER Home & Garden app (see chapter KÄRCHER Home & Garden app).

2. Start the KÄRCHER Home & Garden app.

3. Log in to the KÄRCHER Home & Garden app. If necessary, create an account for this.

4. Scan the enclosed QR code.

   The high-pressure cleaner is registered.

   Note

   If you do not have the enclosed QR code at hand, you can also register the device with the part number and serial number. Both numbers are given on the type plate.

5. Follow the instructions of the KÄRCHER Home & Garden app.

   Note

   Be sure to do this before connecting the high-pressure gun ^® Activate on your mobile device.

Connecting the high-pressure gun

Note

You can find a detailed description of the connection at https://www.kaercher.com/FCR.

6. Plug the mains plug for the high-pressure cleaner into a socket.

   The device switches to coupling mode for 60 s. During this time it is possible to couple the high-pressure gun.

7. Press the "+" key and the "-" key on the high-pressure gun simultaneously for at least 3 s.

   If the coupling is successful, the pressure levels, as well as the radio and the ^®symbol, will be shown on the display.

   ---

   

   The ^®connection between the mobile device and the high-pressure cleaner is established automatically.

   Note

   If necessary, you can also establish the ^®connection at a later time by pressing the "-" key for 10 s.

8. If the coupling attempt failed:

   1. Pull the mains plug for the high-pressure cleaner out of the socket.

   2. Wait 20 s.

   3. Couple the high-pressure gun again.

1. Place the device on a level surface.

2. Completely unwind the high-pressure.

3. Pull the high-pressure hose completely forward through the hose guide and eliminate any loops and twists.

4. Insert the high-pressure hose into the high-pressure gun until it audibly clicks into place.

   Note

   Take care to ensure the correct alignment of the nipple.

   ---

   

5. Check the secure connection by pulling on the high-pressure hose.

6. Plug the mains plug into a mains socket.

The "+/-" buttons on the high-pressure gun can be used to select the pressure and detergent dosing levels. The spray type can be changed by turning the 3-in-1 multi jet spray lance.

Flat jet nozzle
Pressure level	Display	Recommended for e.g.
		Stone terraces, asphalt, metal surfaces, garden utensils (wheelbarrow, spade, etc.)
		Cars / motorcycles, brick surfaces, plastered walls, plastic furniture
		Wooden surfaces, bicycle, sandstone surfaces, rattan furniture

Dirt blaster
Pressure level	Display	Recommended for e.g.
		For particularly stubborn dirt on stone terraces, asphalt, metal surfaces, garden utensils (wheelbarrow, spade, etc.)

Detergent nozzle
Pressure level	Display	Recommended for e.g.
		Operation with detergent. Dosing the detergent concentration as needed

1. Insert the 3-in-1 Multi Jet spray lance and turn it 90° to fix it in place. Be aware of the orientation!

   ---

   

2. ATTENTION

   Spray type change when the lever of the high-pressure gun is pressed

   Damage to the spray lance

   Let go of the lever of the high-pressure gun before changing the spray type.

   Select the spray type. Do this by turning the 3-in-1 Multi Jet spray lance until the required spray display is visible above.

   ---

   

3. Switch the device on ("I/ON").

4. Unlock the lever of the high-pressure gun.

5. Press the lever of the high-pressure gun.

   The device switches on.

For cleaning stubborn dirt, the BOOST function can be activated for 30 seconds regardless of the pressure level set. This increases the water pressure.

1. Hold down the “+” button on the high-pressure gun until BOOST is highlighted on the LCD display.

   ---

   

   After the BOOST function has expired, the device works with the previously set pressure level.

As soon as the display stops flashing, the BOOST function is available again.

1. Remove the cover from the Plug ‘n’ Clean detergent bottle.

2. Plug the detergent bottle into the Plug ‘n’ Clean detergent connection with the opening facing down.

   ---

   

3. Turn the 3-in-1 Multi Jet spray lance to the "MIX" cleaning nozzle until the "MIX" LCD on the pressure indicator of the high-pressure gun lights up.

   The detergent solution is mixed with the water jet during operation.

4. Using the “+/-” buttons of the high-pressure gun, set the desired detergent concentration.

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).

2. Rinse off the loosened dirt with the high-pressure jet.

1. Pull the Plug 'n' Clean detergent bottle out of the holder and close it with the lid.

2. For storage, place the detergent bottle in the holder with the lid facing upwards.

3. Rinse the device with clean water for about 30 seconds.

1. Release the lever of the high-pressure gun.

   When the lever is released, the device switches off. The high-pressure in the system is maintained.

2. Lock the lever of the high-pressure gun.

   ---

   

3. Set the high-pressure gun with the spray lance in the parking position.

4. For work breaks longer than 5 minutes, switch off the device "0/OFF".

1. Release the lever of the high-pressure gun.

2. Close the water tap.

3. Press the lever of the high-pressure gun for 30 seconds.

   The pressure in the system is released.

4. Release the lever of the high-pressure gun.

5. Lock the lever of the high-pressure gun.

6. Switch off the device "0/OFF".

7. Disconnect the device from the water supply.

8. Pull the mains plug out of the outlet.

1. Lift up the device by the carrying handle, and carry it.

1. Pull out the transport handle until it audibly engages.

2. Pull the device by the transport handle.

1. Before horizontal transport, pull the Plug 'n' Clean detergent bottle out of the holder and close it with the lid.

2. Secure the device against shifting and tipping.

1. Place the device on a level surface.

2. Disconnect the spray lance from the high-pressure gun.

3. Press the separation button on the high-pressure gun and disconnect the high-pressure hose from the high-pressure gun.

4. Without a hose reel: Store the high-pressure hose on the device.

5. ATTENTION

   Damage to the high-pressure hose

   Damage to the high-pressure hose through incorrect direction of rotation

   Observe the correct direction of rotation of the hose reel when winding on the hose.

   With a hose reel: Use the crank handle to turn the hose reel counterclockwise and wind up the high-pressure hose.

6. Stow the mains connection and accessories on the device.

Before prolonged storage, observe additional instructions, see chapter Care and service.

The following must be met:

• The device is disconnected from the water supply.

• The high-pressure gun is separated from the high-pressure hose.

1. Switch on the device “I/ON”.

2. Wait a maximum of 1 minute until no more water comes out of the high-pressure hose.

3. Switch off the device.

4. Store the device with all accessories in a frost-proof room.

The device is maintenance-free, i.e. you do not need to perform any maintenance work.

Clean the sieve in the water connection if necessary.

1. Unscrew the coupling on the water connection.

2. Pull out the sieve.

   ---

   

3. Clean the sieve under running water.

4. Insert the sieve into the water connection.

Two non-rechargeable or rechargeable AAA batteries are required.

---

1. Press the locking slide.

   ---

   

2. Open the battery compartment.

3. Remove the battery.

4. Insert new batteries, while paying attention to the correct alignment of the poles.

5. Close the battery compartment.

6. Dispose of the used batteries in accordance with statutory provisions.

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorized Customer Service.

• Device not running 

• The device does not start up, the motor buzzes 

• Device does not reach required pressure 

• Strong pressure fluctuations 

• Device leaking 

• Detergent is not sucked in 

• No pressure indicator on the high-pressure gun 

• BOOST function is not shown on the display and cannot be started via the KÄRCHER Home & Garden app 

• Error messages 

• Emergency operation 

• The high-pressure gun is not working properly 

Remedy:

1. Press the lever of the high-pressure gun.

   The device switches on.

2. Check that the voltage specified on the type plate corresponds to the voltage of the power source.

3. Check the mains connection cable for damage.

4. If the motor is overloaded and the motor circuit breaker has triggered:

   1. Switch off the device "0/OFF".

   2. Allow the device to cool down for 1 hour.

   3. Switch the device on "I/ON" and resume operation.

   Have the device checked by Customer Service if this fault occurs repeatedly.

Cause:

Voltage drop due to a weak mains grid or when using an extension cable

Remedy:

1. When switching on, first press the lever on the high-pressure gun and then switch on the device "I/ON".

Cause:

The water supply is too low.

Remedy:

1. Open the water tap fully.

2. Check the water inlet for an adequate flow rate.

3. Check the setting at the spray lance.

4. Check that the maximum suction height is not exceeded.

Cause:

The sieve in the water connection is dirty.

Remedy:

1. Pull the sieve in the water connection out using flat pliers.

2. Clean the sieve under running water.

   ---

   

Cause:

Air is in the device.

Remedy:

1. Vent the device:

   1. Switch on the device without a connected spray lance for a maximum of 2 minutes.

   2. Press the high-pressure gun and wait until the water escaping from the high-pressure gun is free of air bubbles.

   3. Connect the spray lance.

Remedy:

1. Cleaning the high-pressure nozzle:

   1. Remove contamination from the nozzle drill with a needle.

   2. Rinse the high-pressure nozzle with water from the front.

2. Check the water supply volume.

Remedy:

1. The device leaks a small amount for technical reasons. If the leak is severe, request authorised Customer Service.

Remedy:

1. Turn the 3-in-1 Multi Jet spray lance to detergent nozzle "MIX".

2. Check that the Plug ‘n’ Clean detergent bottle is sitting correctly with the opening facing down in the detergent connection.

Cause:

---

Remedy:

1. Check the batteries and replace them if necessary.

2. Reduce the distance between the high-pressure gun and the high-pressure cleaner.

3. Re-establish the connection to the high-pressure cleaner, see chapter Initial Start-Up.

Cause:

The device is overheated.

Remedy:

1. Check the water supply temperature (for maximum water inlet temperature, see chapter Technical data).

2. Reduce the water supply temperature to give the motor more cooling.

Cause:

---

Remedy:

1. Switch off the device "0/OFF".

2. Pull the mains plug out of the socket.

3. After 20 seconds, insert the mains plug back into the socket.

4. Switch the device on "I/ON".

   Have the device checked by Customer Service if this fault occurs repeatedly.

Cause:

If the pressure regulation on the high-pressure gun is defective, the high-pressure cleaner works at maximum level.

Remedy:

1. Deactivating emergency operation:

   1. Switch off the device "0/OFF".

   2. Pull the mains plug out of the socket.

   3. After 20 seconds, insert the mains plug back into the socket.

   4. Switch the device on "I/ON".

      Have the device checked by Customer Service if this fault occurs repeatedly.

Cause:

---

An internal error has occurred in the electronics of the high-pressure gun.

Remedy:

1. Press the locking slide.

   ---

   

2. Open the battery compartment.

3. Remove the battery.

4. Insert the batteries, paying attention to the correct alignment of the poles.

5. Close the battery compartment.

   Have the high-pressure gun checked by Customer Service if this fault occurs repeatedly.

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

Further information can be found at: www.kaercher.com/dealersearch

Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".

• K 7 Smart Control Flex 

• K 7 Premium Smart Control Flex 

We hereby declare that the product named below complies with the relevant provisions of the directives and regulations listed. This declaration is invalidated by any changes made to the product that are not approved by us.

Product: High-pressure cleaner

Type: 1.317-xxx K 7 (Premium) Smart Control

S.I. 2008/1597 (as amended)

S.I. 2017/1206 (as amended)

S.I. 2012/3032 (as amended)

S.I. 2001/1701 (as amended)

S.I. 2010/2617 (as amended)

(EU) 2019/1781

EN 60335-1

EN 60335-2-79

EN 62233: 2008

EN 300 220-2 V3.1.1

EN 300 328 V2.2.2

EN IEC 63000: 2018

S.I. 2001/1701 (as amended): Schedule 8

Measured: 94

Guaranteed: 97

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Tel.: +49 7195 14-0

Fax: +49 7195 14-2212

---

We hereby declare that the product named below complies with the relevant provisions of the directives and regulations listed. This declaration is invalidated by any changes made to the product that are not approved by us.

Product: High-pressure cleaner

Type: 1.317-xxx K 7 (Premium) Smart Control

2006/42/EC (+2009/127/EC)

2014/53/EU

2011/65/EU

2000/14/EC

2009/125/EC

(EU) 2019/1781

EN 60335-1

EN 60335-2-79

EN 62233: 2008

EN 300 220-2 V3.1.1

EN 300 328 V2.2.2

EN IEC 63000: 2018

2000/14/EG: Annex V

Measured: 94

Guaranteed: 97

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Tel.: +49 7195 14-0

Fax: +49 7195 14-2212

---