Read this safety chapter and these original instructions before using the device for the first time. Act in accordance with them. Keep the original instructions for future reference or for future owners.

• In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.

• Warnings and information notices attached to the device provide important information for hazard-free operation.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Cleaning work producing in oily waste water, e.g. washing engines, washing undercarriages etc., may only be performed at washing stations with an oil separator.

Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil.

Extraction of water from public waterways is not permitted in some countries.

Current information on content materials can be found at: www.kaercher.de/REACH

Use the high-pressure cleaner in private households only.

The high-pressure cleaner is intended for cleaning machines, vehicles, buildings, tools, façades, terraces, garden machines etc. using a high-pressure water jet.

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

The maximum amount of equipment is described in these operating instructions. Depending on the model used, there are differences in the scope of delivery (see packaging).

---

---

1. Stand with carrying handle
2. Water connection with built-in strainer
3. Transport wheel
4. Hose guide
5. Trigger "0/OFF" / "I/ON"
6. Storage for spray lances
7. High-pressure hose
8. *Plug 'n' Clean detergent bottle
9. Storage / parking position for high-pressure gun
10. Transport handle, extendable
11. Spray lance dirt blaster for stubborn soiling
12. Vario Power spray lance for common cleaning tasksThe working pressure can be continuously increased from "SOFT" to "HARD". To adjust the working pressure, release the trigger gun lever and turn the spray lance to the desired position. Detergent can be added to the water jet when the spray lance is turned all the way in the SOFT direction.
13. High-pressure gun
14. Button for separating the high-pressure hose from the high-pressure gun
15. High-pressure gun lever
16. High-pressure gun lock
17. Carrying handle
18. Hose switch
19. High pressure hose reel
20. Crank handle for hose reel
21. Type plate
22. Accessory compartment
23. Hook for net attachment
24. Mesh for accessory compartment
25. Mains connection cable with mains plug
26. Coupling for the water connection
27. *Garden hose (fabric reinforced, diameter at least 1/2 inch (13 mm), length at least 7.5 m, with commercially available quick coupling)
28. *KÄRCHER suction hose for water supply from open containers (order no. 2.643-100)

* additionally required

The power switch prevents unintentional operation of the device.

The lock locks the lever of the high-pressure gun and prevents the device from starting unintentionally.

If the lever of the high-pressure gun is released, the pressure switch turns off the pump and the high-pressure jet stops. The pump switches on again when the lever is pressed.

The motor circuit breaker shuts off the device if power consumption it too high.

Fit the supplied loose parts onto the device before starting up the device.

Have the included screws and the appropriate screwdriver ready.

1. Hang the accessory net on the hooks.

   ---

   

1. Insert the high-pressure hose through the hose guide from the rear.

   ---

   

1. Screw the water connection coupling onto the water connection on the device.

   ---

   

1. Place the device on a level surface.

2. Completely unwind the high-pressure.

3. Pull the high-pressure hose completely forward through the hose guide and eliminate any loops and twists.

4. Insert the high-pressure hose into the high-pressure gun until it audibly clicks into place.

   Note

   Take care to ensure the correct alignment of the nipple.

   ---

   

5. Check the secure connection by pulling on the high-pressure hose.

6. Plug the mains plug into a mains socket.

1. Insert a spray lance into the high-pressure gun and lock it by turning it 90°.

   ---

   

2. Switch the device on ("I/ON").

3. Unlock the lever of the high-pressure gun.

4. Press the lever of the high-pressure gun.

   The device switches on.

1. Remove the lid from the Plug 'n' Clean detergent bottle.

2. Press the detergent bottle into the Plug 'n' Clean detergent connection with the opening facing downwards.

   ---

   

3. Use the Vario Power spray lance.

4. Turn the spray lance all the way into the "SOFT" position.

   The detergent solution is mixed with the water jet during operation.

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).

2. Rinse off the loosened dirt with the high-pressure jet.

1. Flush the device with clear water for approx. 30 seconds.

1. Release the lever of the high-pressure gun.

   When the lever is released, the device switches off. The high-pressure in the system is maintained.

2. Lock the lever of the high-pressure gun.

   ---

   

3. Set the high-pressure gun with the spray lance in the parking position.

4. For work breaks longer than 5 minutes, switch off the device "0/OFF".

1. Release the lever of the high-pressure gun.

2. Close the water tap.

3. Press the lever of the high-pressure gun for 30 seconds.

   The pressure in the system is released.

4. Release the lever of the high-pressure gun.

5. Lock the lever of the high-pressure gun.

6. Switch off the device "0/OFF".

7. Disconnect the device from the water supply.

8. Pull the mains plug out of the outlet.

1. Pull out the transport handle until it audibly engages.

2. Pull the device by the transport handle.

1. Lift and carry the device by the carrying handles.

1. Before horizontal transport, pull the Plug 'n' Clean detergent bottle out of the holder and close it with the lid.

2. Secure the device against shifting and tipping.

1. Place the device on a level surface.

2. Disconnect the spray lance from the high-pressure gun.

3. Press the separation button on the high-pressure gun and disconnect the high-pressure hose from the high-pressure gun.

4. Without a hose reel: Store the high-pressure hose on the device.

5. ATTENTION

   Damage to the high-pressure hose

   Damage to the high-pressure hose through incorrect direction of rotation

   Observe the correct direction of rotation of the hose reel when winding on the hose.

   With a hose reel: Use the crank handle to turn the hose reel counterclockwise and wind up the high-pressure hose.

6. Stow the mains connection and accessories on the device.

7. Put both spray lances into the storage for the spray lance:

   1. Spray lance dirt grinder: Nozzle downwards

   2. Spray lance Vario Power: Nozzle upwards

Before prolonged storage, observe additional instructions, see chapter Care and service.

The following must be met:

• The device is disconnected from the water supply.

• The high-pressure gun is separated from the high-pressure hose.

1. Switch on the device “I/ON”.

2. Wait a maximum of 1 minute until no more water comes out of the high-pressure hose.

3. Switch off the device.

4. Store the device with all accessories in a frost-proof room.

The device is maintenance-free, i.e. you do not need to perform any maintenance work.

Clean the sieve in the water connection if necessary.

1. Unscrew the coupling on the water connection.

2. Pull out the sieve.

   ---

   

3. Clean the sieve under running water.

4. Insert the sieve into the water connection.

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorized Customer Service.

• Device not running 

• The device does not start up, the motor buzzes 

• Device does not reach required pressure 

• Strong pressure fluctuations 

• Device leaking 

• Detergent is not sucked in 

Remedy:

1. Press the lever of the high-pressure gun.

   The device switches on.

2. Check that the voltage specified on the type plate corresponds to the voltage of the power source.

3. Check the mains connection cable for damage.

4. If the motor is overloaded and the motor circuit breaker has triggered:

   1. Switch off the device "0/OFF".

   2. Allow the device to cool down for 1 hour.

   3. Switch the device on "I/ON" and resume operation.

   Have the device checked by Customer Service if this fault occurs repeatedly.

Cause:

Voltage drop due to a weak mains grid or when using an extension cable

Remedy:

1. When switching on, first press the lever on the high-pressure gun and then switch on the device "I/ON".

Cause:

The water supply is too low.

Remedy:

1. Open the water tap fully.

2. Check the water inlet for an adequate flow rate.

3. Check the setting at the spray lance.

4. Check that the maximum suction height is not exceeded.

Cause:

The sieve in the water connection is dirty.

Remedy:

1. Pull the sieve in the water connection out using flat pliers.

2. Clean the sieve under running water.

   ---

   

Cause:

Air is in the device.

Remedy:

1. Vent the device:

   1. Switch on the device without a connected spray lance for a maximum of 2 minutes.

   2. Press the high-pressure gun and wait until the water escaping from the high-pressure gun is free of air bubbles.

   3. Connect the spray lance.

Remedy:

1. Cleaning the high-pressure nozzle:

   1. Remove contamination from the nozzle drill with a needle.

   2. Rinse the high-pressure nozzle with water from the front.

2. Check the water supply volume.

Remedy:

1. The device leaks a small amount for technical reasons. If the leak is severe, request authorised Customer Service.

Remedy:

1. Use the Vario Power spray lance and turn it to "MIX".

2. Check that the Plug 'n' Clean detergent bottle is seated in the connection for the detergent with the opening facing down.

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

Further information can be found at: www.kaercher.com/dealersearch

Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".

• K 7 Power Flex 

• K 7 Premium Power Flex 

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

Product: High-pressure cleaner

Type: 1.317-xxx

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/EC

(EU) 2019/1781

EN 60335-1

EN 60335-2-79

EN 62233: 2008

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 1997 + A1: 2001 + A2: 2008

EN 61000-3-2: 2014

EN 61000-3-11: 2000

EN IEC 63000: 2018

2000/14/EG: Annex V

Measured: 93

Guaranteed: 96

The signatories act on behalf of and with the authority of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2022/10/01