Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.

Keep both books for future reference or for future owners.

Read these safety instructions and the original instructions before using the device for the first time. Act in accordance with them. Keep the two booklets for future reference or for future owners.

• In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.

• Warnings and information notices attached to the device provide important information for hazard-free operation.

• The battery/battery pack is either permanently installed or removable, depending on the device type. Permanently installed batteries/battery packs must not be replaced. Please refer to the operating instructions of the device to find out what applies to your device.

A battery consists of a single storage element, whereas a battery pack consists of interconnected storage elements.

In the following chapters, both terms are used synonymously.

(Depending on the charger)

	Protect the device from moisture. Store the device in a dry place. Do not subject the device to rain. The device is only suitable for indoor use.
	The device has a built-in fuse. The value (X) in amperes can be found on the respective charger.
	The device meets the requirements of protection class II.

(Depending on device/battery type)

	Do not throw the battery into water.
	Do not throw the battery into fire.
	Do not charge defective battery packs.
	Only use the battery pack with the approved chargers. Information on which type of charger/adapter is to be used can be found on the type plate of the charger supplied and/or in the technical data in the operating instructions for the device.

The lithium-ion battery is subject to the requirements of dangerous goods regulations.

The battery pack can be transported by the user in public traffic areas without any further restrictions.

When shipping by third parties (transport companies), special requirements for packaging and labelling must be observed.

Do not use the battery pack if the casing is damaged.

Tape off open contacts.

Pack the battery tightly and securely. The battery pack must not be able to move in the packaging.

Observe the national regulations.

• Only use the device in private households.

• The device is intended exclusively for cleaning dry surfaces

• The following are not in accordance with the intended use:

  • Cleaning people, animals, plants or clothing on the body.

  • Soaking up water or other fluids.

  • Extraction of glowing ashes, coal, cigarettes or other flammable or easily inflammable substances.

  • Use in the vicinity of explosive or highly flammable substances.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

Further information can be found at: www.kaercher.com/dealersearch

Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

The scope of delivery of the unit (dependent on model) is shown on the packaging. These operating instructions describe all possible options.

---

1. Control panel for:
2. On / Off switch
3. Battery LED indicator lamp
4. Buttons for suction strength adjustment (3 levels)
5. Handle
6. Charging connection for USB plug (type C)
7. Built-in battery
8. Exhaust filter cover
9. Dust container unlocking button
10. Dust container suction fitting
11. Dust container
12. Dust container cover flap unlocking button
13. Dust container cover flap
14. Fine filter
15. Pre-filter
16. Motorised floor nozzle with universal brush roller
17. Suction pipe
18. Crevice nozzle
19. 2-in-1 furniture nozzle
20. Wall bracket
21. Charger (type C)
22. Charging cable (type C)

The scope of delivery includes a wall bracket as well as screws and dowels for tidy storage of the vacuum cleaner.

---

---

• Push the suction pipe on to the suction fitting of the dust container until it audibly clicks into place.

• Press the unlocking button and remove the suction pipe from the suction fitting.

  ---

  

• Push the motorised floor nozzle on to the suction pipe until it audibly clicks into place.

• Press the unlocking button and remove the motorised floor nozzle from the suction pipe.

  ---

  

• Push the accessory, such as the crevice nozzle, on to the suction fitting of the dust container or suction pipe until it audibly clicks into place.

  ---

  

1. To charge the device, attach it to the wall bracket included in the scope of delivery.

   ---

   

2. Insert both USB plugs of the charging cable into the charging port of the device and charger.

   Plug the charger into the mains socket.

   The LED battery indicator flashes green during the charging process.

   ---

   

3. When the device is fully charged, the LED battery indicator lights up continuously green for 120 min. The LED then goes out.

   Remove both USB plugs of the charging cable from the charging port of the device and charger.

   Remove the charger from the main socket.

   Remove the device from the wall bracket.

   ---

   

The device is ready for use.

The following table describes the meaning of the LED indicators (green and red) on the device:

1. Install the desired accessory, see chapter Installing accessories.

2. Switch on the device:

   • Press the On / Off switch.

   ---

   

3. If necessary, use the "+ / -" button on the control panel to set the suction power.

   Note

   The device has 3 suction strengths.

   1. Eco mode: For cleaning small amounts of dust.

   2. Standard mode: For daily cleaning.

   3. Boost mode: Maximum power for high-performance cleaning (with this suction power setting, the battery is discharged more quickly than with other settings).

   Note

   When the device is switched on, the suction power is always in standard mode (level 2).

   ---

   

To change accessories, see chapter Installing accessories

1. Switch off the device.

   • Press the On / Off switch.

     ---

     

   ATTENTION

   Device damage

   If the pre-filter and fine filter are not cleaned regularly after vacuuming or the dust container is not emptied, the suction power will deteriorate and the device may break down.

   Clean the pre-filter and fine filter at least once a week.Empty the dust container at the latest when the "MAX" marking is reached.

2. Remove the suction pipe or accessory.

3. Empty the dust container.

   • Press the unlocking button. The flap of the dust container opens.

   • Empty the dust container into a waste container.

     ---

     

4. To close, push flap of the dust container up until it clicks into place.

5. Clean the pre and fine filter, see chapter Clean the pre-filter, fine filter and dust container

6. Attach the device to the wall bracket.

   ---

   

7. Store accessories on the wall bracket.

   ---

   

8. Charge the device, see chapterBattery charging

• Which accessories are included in the scope of delivery is shown on the device packaging.

• Test the accessory at an inconspicuous point before using it in a sensitive area.

• Follow the manufacturer's cleaning instructions.

• Connect the motorised nozzles to the suction pipe or the hand-held device.

• Also connect the other accessory parts, such as crevice nozzle, to the hand-held device or push it directly onto the suction pipe to increase the reach.

Ideal for hard floors and carpets.

The motorised floor nozzle removes dirt stuck between the carpet fibres particularly effectively.

For edges, joints, heaters and areas that are difficult to reach.

For gentle cleaning of sofas and delicate furniture. Depending on requirements, the accessory can be used as a furniture or upholstery brush by pressing the button.

The battery has been tested in accordance with the relevant rules for international transport, and can be transported / shipped.

The battery pack display shows the current charging state during storage.

---

1. Switch off the device:

   • Press the On / Off switch.

     ---

     

2. Remove the dust container:

   • Press the unlocking button on the dust container and unlock and remove by turning in the direction of the "lock open" symbol.

     ATTENTION

     Device damage

     If the device is turned 180 degrees for filter cleaning (fine filter pointing upwards), fine dust can fall into the motor area and damage the device.

     Always hold the device downwards when cleaning / removing the fine filter.

     ---

     

     ---

     

3. Remove the fine filter and pre-filter:

   • Unlock the fine filter by turning it counter-clockwise and remove it.

   • Press the unlocking button to open the flap of the dust container. Pull the pre-filter downward and remove it from the dust container.

     ---

     

4. Cleaning the dust container, pre-filter and fine filter.

   • Any tangled threads or hairs on the pre-filter can be carefully cut off with scissors.

   • Carefully knock out the pre-filter and fine filter on a waste paper basket.

     ---

     

   • Wipe out the dust container with a cloth.

   • If necessary, carefully clean the pre-filter and fine filter with a soft cloth or brush.

     ---

     

5. Attach the fine filter to the device.

   • Check for correct seating.

6. Insert the pre-filter into the dust container.

   • Check for correct seating.

7. Attach the dust container:

   • Place the dust container on the device and turn in the direction of the "Lock closed" symbol. Check for correct seating.

1. Switch off the device:

   • Press the On / Off switch.

     ---

     

2. Remove the exhaust filter:

   • Unscrew and remove the exhaust filter cover from the device.

   • Remove the exhaust filter from the cover.

     ---

     

3. Cleaning the exhaust filter:

   • Carefully tap off the exhaust filter or, if it is very dirty, carefully clean it together with the cover using a soft cloth or brush.

   • ---

     

4. Clean the exhaust filter:

   • Plug the exhaust filter and cover together and screw onto the device head. Check for correct seating.

1. Switch off the device.

   • Press the On / Off switch.

     ---

     

2. Remove accessories.

3. ATTENTION

   Short circuit hazard

   The motorised floor nozzle contains electrical components.

   Do not immerse the motorised floor nozzle in water or clean it with a damp cloth.

   Clean the motorised floor nozzle.

   1. Slide the release button in the direction of the "lock open" symbol and remove the roller brush.

      ---

      

   2. Remove the dirt e.g. with a brush. Any tangled threads or hairs can be carefully cut off with scissors.

   3. Carefully clean the brush opening with a cloth or soft brush.

      ---

      

   4. Insert the roller brush into the brush opening, press down and allow to engage. Check for correct seating.

      ---

      

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

• The device does not start up 

• Device does not suck 

• The battery is not charging 

• Charging time is changed 

• LED flashes red at short intervals / device stops during operation / device has low suction power 

• Fine filter gets dirty / dusty quickly 

• Dust container cannot be inserted. 

• Abnormal engine noise 

Cause:

Battery is empty.

Remedy:

• Charge the rechargeable battery.

Cause:

Fine filter was not inserted or not inserted correctly.

Remedy:

• Insert the fine filter.

• Check that the fine filter is seated correctly.

Cause:

The charging plug/mains plug is not connected correctly.

Remedy:

• Connect the charging plug/mains plug correctly.

Cause:

The socket is defective.

Remedy:

• Check that the socket is working.

Cause:

The wrong charger is being used

Remedy:

• Check that the correct charger is being used.

Cause:

Use of a USB plug (type C) or charger outside the scope of delivery.

Remedy:

• For a specified charging time, use the USB plug (type C) / charger included in the scope of delivery.

Cause:

The accessories, the suction opening on the dust container or the suction pipes are clogged.

Remedy:

• Remove the blockage/clog with a suitable aid.

Cause:

Battery/device is overheated or undercooled.

Remedy:

• Switch off the device and disconnect from the current supply.

Remedy:

• Wait until the battery temperature/device temperature is back within the normal range.

Cause:

The dust container is full.

Remedy:

• Empty the dust container.

Cause:

The filters are soiled.

Remedy:

• Clean the filter.

Cause:

Roller brush is blocked.

Remedy:

• Remove any blockage.

Cause:

Pre-filter was not used.

Remedy:

• ​Insert the pre-filter.

Cause:

Filter unit is not complete.

Remedy:

• Check whether the filter unit (pre-filter and fine filter) is complete.

Cause:

The accessories, the suction opening on the dust container or the suction pipes are clogged.

Remedy:

• Remove the clog with a suitable aid.