K 2 BatteryK 2 Battery Set

59799640 (04/25)

59799640 (04/25)
With the KÄRCHER Home & Garden app, you benefit from the following advantages when using your device:
Application tips & expert knowledge
Product information, overview of accessories and operating instructions
Support and service contact
Online shop - exclusive offers and much more
Download the KÄRCHER Home & Garden app from your app store and conveniently register your product.
Read these original instructions and the enclosed original instructions for the battery pack/charger before using the device for the first time. Act in accordance with them. Keep the booklets for future reference or for future owners.
In addition to the notes in the operating instructions, you also need to take into consideration the general safety regulations and accident prevention guidelines applicable by law.
Warnings and information notices attached to the device provide important information for hazard-free operation.
Indication of an imminent threat of danger that will lead to severe injuries or even death.
Indication of a potentially dangerous situation that may lead to severe injuries or even death.
Indication of a potentially dangerous situation that may lead to minor injuries.
Indication of a potentially dangerous situation that may lead to damage to property.
Wear suitable protective clothing and safety goggles to protect yourself from water or dirt backsplash.
Aerosols can be formed when using high-pressure cleaners. Inhaling aerosols can be harmful for your health. Depending on the application, the use of fully shielded nozzles (e.g. surface cleaners) can significantly lower the emission of aqueous aerosols. Depending on the environment to be cleaned, wear a suitable respiratory protective mask of class FFP 2 or comparable to protect yourself from inhaling aerosols if the use of a fully shielded nozzle is not possible.
Risk of asphyxiation. Keep packaging film out of the reach of children.
Only use the device for its proper use. Take into account the local conditions and beware of third parties, in particular children, when working with the device.
Persons with reduced physical, sensory or mental capabilities and persons lacking experience and knowledge may only use the appliance if they are properly supervised, have been instructed on use of the appliance safely by a person responsible for their safety, and understand the resultant hazards involved.
Children must not operate the device.
Children must be supervised to prevent them from playing with the appliance.
Safety devices are provided for your own protection. Never modify or bypass safety devices.
Operation in explosive atmospheres is prohibited.
Never suction solvents, liquids containing solvents or undiluted acids. This includes e.g. petrol, paint thinner or heating oil. The spray mist is highly flammable, explosive and poisonous.
Damaged wheels / tyre valves are extremely dangerous. Damaged wheels / tyre valves can be damaged by the high-pressure jet and explode. The first sign of this is discolouration of the tyres. Keep a spray distance of at least 30 cm when cleaning the wheels / tyre valves.
Do not use the device if people without the proper protective clothing are in its reach.
Do not aim the high-pressure jet at yourself, e.g. to clean clothes or shoes.
Do not direct the high-pressure jet at persons, animals, live electrical equipment or at the device itself.
Do not spray any objects which contain harmful substances (e.g. asbestos).
Check the device and the accessories, such as the high-pressure hose, high-pressure gun and safety devices, to make sure they are in proper safe and reliable condition before each operation. Do not use the device if it is damaged. Replace damaged components immediately.
Only use high-pressure hoses, control panels and couplings specified by the manufacturer.
Risk of scalding. When disconnecting the supply or high-pressure hose, hot water can leak out of the connections after operation.
According to the applicable regulations, the appliance may never be used with the drinking water network without a system separator. Ensure that the connection to your house water system, with which the high-pressure cleaner is operated, is equipped with a system separator according to EN 12729 type BA.
Water that has flowed through a system separator is no longer classified as drinkable.
Never leave the device unsupervised while it is in operation.
Recoil force from the water stream emerging at the high-pressure nozzle acts on the high-pressure gun. Keep proper footing and hold the high-pressure gun and spray lance firmly.
Accidents or damage due to the device falling over. Before all actions with or on the device, you must make sure that it is stable.
Do not operate the device at temperatures below 0 °C.
Incorrect use of detergents can cause serious injuries or poisoning.
Keep the detergent out of the reach of children.
Only use the detergents supplied or specified by the manufacturer. The use of other detergents or chemicals can impair the safety of the device.
Risk of accidents and injuries. Take into account the weight of the device for transportation and storage. See chapter Technical data in the operating instructions.
The power switch prevents unintentional operation of the device.
The lock locks the lever of the high-pressure gun and prevents the device from starting unintentionally.
If the lever of the high-pressure gun is released, the pressure switch turns off the pump and the high-pressure jet stops. The pump switches on again when the lever is pressed.
The device shuts off automatically after 2 minutes of dry running so as to prevent damage to the high-pressure pump.
![]() | Do not aim the high-pressure jet may at persons, animals, live electrical equipment or the device itself. Protect the device against frost. |
![]() | The device may not be connected to the public drinking water network. |
The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.
Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.
Cleaning work producing in oily waste water, e.g. washing engines, washing undercarriages etc., may only be performed at washing stations with an oil separator.
Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil.
Extraction of water from public waterways is not permitted in some countries.
Current information on content materials can be found at: www.kaercher.de/REACH
Use the high-pressure cleaner in private households only.
The high-pressure cleaner is intended for cleaning machines, vehicles, buildings, tools, façades, terraces, garden machines etc. using a high-pressure water jet.
The device can be operated with a single 36 V Kärcher Battery Power battery pack.
Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.
Information on accessories and spare parts can be found at www.kaercher.com.
The following are available as special accessories:
Battery packs/chargers that are not included in the scope of delivery or that are additionally required
A quick charger and a battery pack with a larger capacity
The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.
The maximum amount of equipment is described in these operating instructions. Depending on the model used, there are differences in the scope of delivery (see packaging).

Fabric reinforced
Diameter of at least 1/2 inch (13 mm)
Length at least 7.5 m
Fit the supplied loose parts onto the device before starting up the device.
Fit the carrying handle so that it latches into place.

Screw the water connection coupling onto the water connection on the device.

Direct sunlight
Overheating
Do not the place the device and battery pack in direct sunlight.Place the device on a level surface.
Connect the high-pressure hose to the device's high-pressure connection.

Insert the high-pressure hose into the high-pressure gun until it audibly clicks into place.
Take care to ensure the correct alignment of the nipple.

Check for a secure connection by pulling on the high-pressure hose.
Charge the battery pack (see operating instructions for the battery pack).
Push the battery pack into the mounting in the device until it audibly latches into place.

For the connection values, see the type plate or chapter Technical data.
Observe the water distribution company regulations.
Damage through contaminated water
Contamination in the water can damage the pump and the accessories.
KÄRCHER recommends using the KÄRCHER water filter for protection(special accessory, order number 4.730-059).Risk of damage when using hose couplings made of brass with AquaStop function from third-party suppliers.
Damage to the high-pressure pump.
Only use hose couplings with/without AquaStop function from Kärcher, hose couplings without AquaStop function or hose couplings made of plastic with AquaStop function from third-party suppliers.Plug the garden hose onto the water connection coupling.
Connect the garden hose to the water line.
Open the water tap completely.

This high-pressure cleaner with the KÄRCHER suction hose is suitable for sucking in surface water, e.g.from water butts or ponds (for maximum suction height, see Technical data).
Unscrew the coupling on the water connection.
Fill the suction hose with water.
Screw the suction hose onto the water connection of the device and hang it in a water source (e.g. rain barrel).
Switch the device on "I/ON".
Unlock the lever of the high-pressure gun.
Press the lever of the high-pressure gun.
The device switches on.
Allow the device for run a maximum of 2 minutes until the water escaping from the high-pressure gun is free of air bubbles.
Release the lever of the high-pressure gun.
Lock the lever of the high-pressure gun.
Dry running of pump
Damage to the device
If the device does not build up any pressure within 2 minutes, switch off the device and proceed according to the instructions in chapterTechnical data.Damage to painted or sensitive surfaces
Surfaces can be damaged when the jet is too close to the surface or an unsuitable spray lance is used.
Maintain a minimum spray distance of 30 cm when cleaning painted surfaces.Do not clean car tyres, paint or sensitive surfaces such as wood with the dirt blaster.Insert a spray lance into the high-pressure gun and lock it into position by turning it 90°.

Switch the device on ("I/ON").
Unlock the lever of the high-pressure gun.
Press the lever of the high-pressure gun.
The device switches on.
The working mode is shown on the high-pressure gun display.
The battery pack may cause a delay of max. 4 seconds when switching on the device.
Failure to adhere to the safety data sheet
Incorrect handling of the detergent can seriously damage your health
Observe the safety data sheet of the detergent manufacturer, in particular the instructions on personal protective equipment.Detergent can only be mixed into the jet at low pressure.
Pull the suction hose for the detergent out of the casing to the desired length.

Hang the detergent suction hose in a container with detergent solution.
Disconnect the spray lance from the high-pressure gun. Work with the high-pressure gun in MIX mode.
The detergent solution is mixed with the water jet during operation.
Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).
Rinse off the loosened dirt with the high-pressure jet.
Flush the device with clear water for approx. 30 seconds.
Release the lever of the high-pressure gun.
The device switches off when the lever is released. The high pressure in the system is retained.
Lock the lever of the high-pressure gun.

Switch the device off "0/OFF" during work breaks longer than 5 minutes.
During longer work breaks, remove the battery pack from the device and secure it against unauthorised use.
Remove the battery pack:
Press the battery pack unlocking button.
Pull the battery pack out of the battery pack mount.

Pressure in the system
Injuries from high-pressure water escaping uncontrollably
Only disconnect the high-pressure hose from the high-pressure gun or the device when the system is fully depressurised.Release the lever of the high-pressure gun.
Close the water tap.
Press the lever of the high-pressure gun for 30 seconds.
The pressure still remaining in the system is released.
Release the lever of the high-pressure gun.
Lock the lever of the high-pressure gun.
Disconnect the device from the water supply.
Switch off the device "0/OFF".
Remove the battery pack (seeRemoving the battery pack).
Charge the battery pack.
Also charge partly discharged battery packs after operation.
Risk of injury or damage due to the weight of the device!
Injury and damage.
Be aware of the weight of the device during transport and storage.Lift up and carry the device by the carrying handle.
Secure the device against slipping and tipping over.
Risk of injury or damage due to the weight of the device!
Injury and damage.
Be aware of the weight of the device during transport and storage.Place the device on a level surface.
Disconnect the spray lance from the high-pressure gun.
Snap the spray lance into the storage for the spray lance.
Press the separation button on the high-pressure gun and disconnect the high-pressure hose from the high-pressure gun.
Place the high-pressure gun in the storage compartment for the high-pressure gun.
Disconnect the high-pressure hose from the device.
Store the high-pressure hose on the device.
Observe the additional notes before storing the device for a longer period of time, see chapter Care and maintenance.
Risk of damage!
Damage to the device due to freezing water.
Completely empty the device and accessories after each use.Protect the device and accessories from frost.Disconnect the device from the water supply.
Disconnect the high pressure-hose.
Switch on the device “I/ON”.
Wait for a maximum of 1 minute until no more water escapes from the high-pressure connection.
Switch off the device.
Store the device and accessories in a frost-protected room.
Improper care and maintenance work
Short-circuit
Switch off the device and remove the battery pack before performing any work on the device.Do not clean the device with water.Improper cleaning
Risk of damage.
Do not use any abrasive or aggressive detergents.Risk of damage due to missing or damaged sieve!
Damage to the high-pressure pump
Do not operate the device without a sieve.Do not clean the sieve with hard, pointed objects.Clean the sieve in the water connection if necessary.
Unscrew the coupling on the water connection.
Pull out the sieve.

Clean the sieve under running water.
Insert the sieve into the water connection.
Clean the detergent filter before prolonged storage.
Remove the filter from the detergent suction hose.
Clean the filter under running water.

Touching live parts
Electric shock
Switch off the device and remove the battery pack before performing any work on the device.Have repair work and work on electrical components carried out by the authorised customer service only.You can remedy minor faults using the following overview.
If in any doubt, please contact your authorised Customer Service.
Device is not running
Cause:
The device is not switched on
Remedy:
Press the lever of the high-pressure gun.
The device switches on.
Cause:
The battery pack is not sitting properly in the device
Remedy:
Push the battery pack into the mounting in the device until it audibly latches into place.
Cause:
The battery pack is overheated
Remedy:
Remove the battery pack from the device and allow it to cool down.
Cause:
The charging state of the battery pack is too low
Remedy:
Charge the battery pack.
Cause:
The battery pack or the charger are defective
Remedy:
Replace the battery pack or charger.
Device switches off automatically
Cause:
The dry-running protection has triggered
Remedy:
Open the water tap completely.
Check the water inlet for sufficient flow rate.
Check that the maximum suction height is not exceeded.
Cause:
There is a danger of the battery pack overheating
Remedy:
Switch off the device "0/OFF".
Allow the battery pack to cool down.
Switch on the device “I/ON”.
The device does not reach required pressure
Cause:
The water supply is too low
Remedy:
Open the water tap completely.
Check the water inlet for sufficient flow rate.
Check that the maximum suction height is not exceeded.
Cause:
The sieve in the water connection is contaminated
Remedy:
Pull out the sieve in the water connection with flat pliers.
Clean the sieve under running water.
Cause:
There's air in the device
Remedy:
Vent the device:
Switch on the device without the high-pressure hose connected for a maximum of 2 minutes and wait until water comes out of the high-pressure connection without bubbles.
Switch off the device.
Connect the high-pressure hose.
During vacuuming operations, observe the max. suction height (see Technical data).
Strong pressure fluctuations
Remedy:
Cleaning the high-pressure nozzle:
Remove contamination from the nozzle drill with a needle.
Rinse the high-pressure nozzle with water from the front.
Check the water supply volume.
Detergent is not sucked in
Remedy:
Disconnect the spray lance from the high-pressure gun and work only with the high-pressure gun.
Clean the filter on the detergent suction hose.
Check the detergent suction hose for kinks.
Device leaking
Remedy:
The device leaks a small amount for technical reasons. If the leak is severe, request authorised Customer Service.
The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.
Further information can be found at: www.kaercher.com/dealersearch
Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".
Device performance data | |
Working voltage of the battery | 36 V |
Power | 1,1 kW |
Protection type | IPX5 |
Operating pressure | 7,4 MPa |
Max. permissible pressure | 11 MPa |
Water flow rate | 5,5 l/min |
Maximum flow rate | 5,8 l/min |
Detergent flow rate | 0,3 l/min |
High-pressure gun recoil force | 11 N |
Operating time when battery fully charged (max.) | |
Working mode MIX | 29 min |
Working mode STANDARD | 14 min |
Working mode BOOST | 8 min |
Water connection | |
Feed pressure (max.) | 1,2 MPa |
Input temperature (max.) | 40 °C |
Suction height (max.) | 0,5 m |
Dimensions and weights | |
Typical operating weight | 6,9 kg |
Length | 245 mm |
Width | 303 mm |
Height | 629 mm |
Determined values in acc. with EN 60335-2-79 | |
Hand-arm vibration value | 1,3 m/s2 |
Uncertainty K | 0,6 m/s2 |
Sound level LpA | 72 dB(A) |
Uncertainty KpA | 3 dB(A) |
Sound power level LWA+ Uncertainty KWA | 88 dB(A) |
We hereby declare that the product named below complies with the relevant provisions of the directives and regulations listed. This declaration is invalidated by any changes made to the product that are not approved by us.
Product: High-pressure cleaner
Type: K 2 Battery
Directives and Regulations2006/42/EC (+2009/127/EC)
2014/30/EU
2011/65/EU
2000/14/EC
Harmonised standards usedEN 60335-1
EN 60335-2-79
EN 62233: 2008
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 1997 + A1: 2001 + A2: 2008
EN IEC 63000: 2018
Conformity evaluation procedure used2000/14/EC: Annex V
Sound power level dB(A)Measured: 85
Guaranteed: 88
Name and addressDocumentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Tel.: +49 7195 14-0
Fax: +49 7195 14-2212

Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 - 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2025/04/01
