Read these original instructions and the enclosed safety instructions before using the device for the first time. Act in accordance with them.

Keep both books for future reference or for future owners.

• If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.

• Notify the dealer immediately in the case of shipping damage.

• Check the package contents when unpacking for missing accessories or for damage.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

• This universal vacuum cleaner for carpets is intended for dry cleaning floor and wall surfaces.

• This device is suitable for commercial use, e.g. in hotels, schools, hospitals, factories, shops, offices, and rental companies.

1. Unpack the device and install the accessories.

   ---

   

1. Check whether the permanent filter basket is attached to the suction head.

1. Operation with the filter bag

2. Operation without the filter bag

1. Unlock and remove the exhaust grille.

2. Remove the exhaust gas filter casing.

3. Insert the HEPA filter (special accessory).

4. Attach and lock the exhaust grille.

1. Unlock and remove the suction head.

2. Fit the fleece filter bag. Pull the opening of the filter bag completely over the shoulder of the suction hose port.

   ---

   

3. Fit the suction head and lock.

1. Slide the battery pack into the battery holder and lock it in place.

1. Press the unlocking button and remove the battery pack.

2. Charge the battery pack according to the operating instructions of the charger manufacturer and the battery pack manufacturer.

1. Switch on the device at the main switch.

Eco button (energy-saving mode): The device works with reduced suction performance. The battery run time is extended.

1. To activate Eco-mode: Actuate the Eco switch. The illuminated ring of the Eco switch lights up blue.

2. To switch off Eco-mode: Actuate the Eco switch repeatedly. The blue illuminated ring goes out.

1. Regulate the suction power on the suction control.

1. Set the floor nozzle switch to hard surface or carpet.

2. Perform cleaning.

1. Switch off the device at the main switch.

1. Empty the container.

2. Vacuum the inside and outside of the device and clean with a moist cloth.

1. Store the device in a dry room and secure it against unauthorised use.

1. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respectively applicable guidelines.

The device may only be stored indoors.

1. Press the unlocking button and remove the battery pack to prevent discharge.

1. Unlock and remove the suction head.

2. Turn the suction head by 180° and set it down.

3. Unlock and remove the permanent filter basket.

4. If necessary, clean the permanent filter basket (washable) under running water and let it dry.

5. Fit the permanent filter basket and snap it into place.

6. Fit the suction head and lock.

1. Unlock and remove the suction head.

2. Remove the fleece filter bag from the suction hose port.

   ---

   

3. Fold in the lock latch and seal the fleece filter bag tight.

4. Fit a new fleece filter bag. Pull the opening of the filter bag completely over the shoulder of the suction hose port.

5. Fit the suction head and lock.

Exhaust filter: replace as required, but at least once a year

1. Unlock and remove the exhaust grille.

2. Remove the exhaust gas filter casing.

3. Remove the exhaust filter from the exhaust gas filter casing.

4. Insert a new exhaust filter in the exhaust filter casing.

5. Insert the exhaust gas filter casing.

6. Attach and lock the exhaust grille.

HEPA filter: replace as required, but at least once a year

1. Unlock and remove the exhaust grille.

2. Remove the HEPA filter (special accessories).

3. Insert a new HEPA filter (special accessory).

4. Attach and lock the exhaust grille.

1. Unlock and remove the suction head.

2. Turn the suction head by 180° and set it down.

3. Unlock and remove the permanent filter basket.

4. Remove the motor protection filter.

5. Fit a new motor protection filter.

6. Fit the permanent filter basket and snap it into place.

7. Fit the suction head and lock.

• The device stops during operation 

• Suction force decreases 

• Escaping dust when vacuuming 

• Suction turbine does not start up 

Cause:

The motor thermo-protector has triggered

Remedy:

1. Check all parts for clogging.

2. Change the fleece filter bag.

3. Replace the motor protection filter.

4. Replace the exhaust filter or the HEPA filter (optional accessory).

5. Switch the device on again.

Remedy:

1. Remove all blockages from the suction nozzle, the suction pipe or the suction hose.

2. Change the fleece filter bag.

3. Clean the permanent filter basket under running water and allow to dry.

4. Position/lock the suction head correctly.

5. Replace a defective suction hose.

6. Replace the motor protection filter.

Remedy:

1. Check the fit of the fleece filter bag.

2. Change the fleece filter bag.

3. Position/lock the suction head correctly.

4. Clean the permanent filter basket under running water and allow to dry.

5. Insert a new permanent filter basket.

6. Correctly insert the motor protection filter or replace.

Remedy:

1. Allow an overheated board to cool down.

2. Charge the battery pack.

3. Insert the battery pack.

4. Turn on the device again.

If the malfunction cannot be corrected, the device must be checked by the Customer Service department.

• The device stops during operation 

• Suction force decreases 

• Escaping dust when vacuuming 

• Suction turbine does not start up 

Cause:

The motor thermo-protector has triggered

Remedy:

1. Check all parts for clogging.

2. Change the fleece filter bag.

3. Replace the motor protection filter.

4. Replace the exhaust filter or the HEPA filter (optional accessory).

5. Switch the device on again.

Remedy:

1. Remove all blockages from the suction nozzle, the suction pipe or the suction hose.

2. Change the fleece filter bag.

3. Clean the permanent filter basket under running water and allow to dry.

4. Position/lock the suction head correctly.

5. Replace a defective suction hose.

6. Replace the motor protection filter.

Remedy:

1. Check the fit of the fleece filter bag.

2. Change the fleece filter bag.

3. Position/lock the suction head correctly.

4. Clean the permanent filter basket under running water and allow to dry.

5. Insert a new permanent filter basket.

6. Correctly insert the motor protection filter or replace.

Remedy:

1. Allow an overheated board to cool down.

2. Charge the battery pack.

3. Insert the battery pack.

4. Turn on the device again.

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

Further information can be found at: www.kaercher.com/dealersearch

Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

Only use KÄRCHER original battery packs, not non-rechargeable batteries.

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

Product: Dry vacuum cleaner

Type: 1.355-xxx

Type: 1.527-xxx

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

EN IEC 63000: 2018

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60312-1: 2017

EN 60335-1

EN 60335-2-69

EN 62233: 2008

-

The signatories act on behalf of and with the authority of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2022/10/01

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

Product: Dry vacuum cleaner

Type: 1.355-xxx

Type: 1.527-xxx

S.I. 2008/1597 (as amended)

S.I. 2012/3032 (as amended)

S.I. 2016/1091 (as amended)

EN IEC 63000: 2018

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 60312-1: 2017

EN 60335-1

EN 60335-2-69

EN 62233: 2008

-

The signatories act on behalf of and with the authority of the company management.

---

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: +49 7195 14-0

Fax: +49 7195 14-2212

Winnenden, 2022/10/01

• T 10/1 Bp (Adv/HEPA) 

• T 15/1 Bp (Adv/HEPA)