Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.

Keep both books for future reference or for future owners.

This mattress vacuum cleaner is intended for private use at home and not for commercial purposes. The manufacturer is not liable for any damage that may occur on account of improper use or incorrect operation. Use the mattress vacuum cleaner only with:

• Original filters

• Original spare parts, accessories and special accessories.

The mattress vacuum cleaner is not suitable for:

• Vacuuming off human beings or animals.

• Vacuuming up:

  • Small living creatures (e.g. flies, spiders, etc.).

  • Substances that are harmful for health, have sharp edges or are hot or glowing.

  • Moist or liquid substances.

  • Easily flammable or explosive substances and gases.

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Current information on content materials can be found at: www.kaercher.de/REACH

Only use original accessories and original spare parts. They ensure that the device will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

---

There is a label under the dust container of the device that describes how to clean/replace the foam filter and motor protection filter:

1. Detach dust container from the device. The motor protection filter is located under the dust container.

2. Open the dust container, remove the cyclone cone, turn it upside down and extract the foam filter

   Danger: The device contains electrical components and must not be cleaned under running water.

3. Clean the motor protection filter and foam filter after each use to ensure maximum airflow efficiency and hygiene standards.

4. Allow both filters to dry for at least 24 hours.

5. Replace the filters if visibly damaged or every 3 months for optimal performance. Accessories available via code.

For detailed instructions, seeCleaning the dust container, foam filter and motor protection filter .

1. Connect to power supply.

2. Press the On/Off button, the device switch on.

3. Move the device on the fabric surfaces, such as mattresses, sofa, pillows and other upholstery.

   ---

   

4. Press the On/Off button again, the device stops.

The UV indication light only activates when in contact with surface and turns off automatically otherwise.

---

The LED on the handle shows status of UV light.

Light indicators	Status	Description
	LED does not light up.	The device is not switch on.
	LED lights up white continuously.	The device is on, the UV light at the bottom of the device is off.
	LED lights up purple continuously.	The device is on, the UV light at the bottom of the device is on.

1. Switch off the device.

2. Hold the dust container firmly and pull it away from the main body.

   ---

   

3. Open the dust container lid.

   1. Press the release button on the back of lid.

   2. Lift the cover upward to detach it from the dust container.

   ---

   

4. Empty the dust container at the latest when the dust reaches the MAX line.

   ---

   

5. To close, place the dust container lid onto the dust container and press down firmly until you hear a click feedback, ensuring a secure and airtight seal.

6. Inert the dust container into device.

7. Clean the foam filter and motor protection filter, (see Cleaning the dust container, foam filter and motor protection filter.)

Before doing any work on the device:

1. Switch off the device.

2. Unplug the power supply from the power outlet.

1. Switch off the machine

2. Remove dust container, (see Emptying dust container).

3. Remove the foam filter and motor protection filter.

   • Firmly pull the cyclone to detach it from the dust container.

   • From the bottom of the cyclone cone, detach the foam filter.

     ---

     

   • At the base of the dust container, remove the motor protection filter.

     ---

     

4. Cleaning the dust container, foam filter and motor protection filter.

   • Wipe out the dust container and cyclone cone with a cloth or rinse them under running water. Ensure they are completely dry before reassembly.

   • Rinse the foam filter and motor protection filter under running water, then dry them thoroughly or replace them if necessary.

     ---

     

     ATTENTION

     These parts are not dishwasher-safe.

     The recommended drying time is 24 hours.

5. Insert the motor protection filter.

   • Install the motor protection filter, ensuring it is securely seated.

     ---

     

6. Attach the cyclone into dust container.

   • Insert the foam filter into the cyclone cone, then attach the cyclone cone to the dust container until it locks firmly in place.

7. Attach the dust container lid.

   • Place the dust container lid onto the dust container and press down firmly until you hear a click, ensuring a secure and airtight seal.

8. Attach the dust container into device.

   • Reattach the dust container to the machine in an upright position until it clicks into place.

     ---

     

1. Switch off the machine.

2. Turn the device upside down.

3. Remove the roller.

   • Slide the release button to unlock position and remove the roller cover.

     ---

     

   • Remove the roller.

     ---

     

4. Clean the roller under rinsing water.

   • Remove the dirt e.g. with a brush. Any tangled threads or hairs can be carefully cut off with scissors.

   • Carefully clean the roller opening with a cloth or soft brush.

     ---

     

   • Insert the roller brush into the roller opening, press down and allow to engage. Place the roller cover and lock it. Check for correct seating.

     ---

     

5. Use a soft, dry cloth to wipe the device and the UV transparent cover.

   ---

   

This device may only be stored indoors.

1. Wind the power cable around the device.

2. Store the device in a dry location that is protected from frost.

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing flaw is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

Further information can be found at: www.kaercher.com/dealersearch

Further warranty information (if available) can be found in the service area of your local Kärcher website under "Downloads".

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

• The device does not work 

• Suction power decreases / the device becomes louder 

• The roller stops rotating 

• UV light does not work / works incorrectly  

• The device shuts down completely 

Cause:

Power plug is not inserted.

Remedy:

Cause:

The outlet is not supplying power.

Remedy:

Cause:

1. The dust container is full of dust.

2. The cyclone component filter is clogged.

3. Motor protection filter is full.

Remedy:

1. Empty and clean the dust container.

2. Remove any blockage in the cyclone cone.

3. Replace the foam filter and motor protection filter.

   SeeCleaning the dust container, foam filter and motor protection filter.

Cause:

Roller is blocked by obstruction (e.g., sheets, toys).

Remedy:

Cause:

The device is not in contact with the surface

Remedy:

Cause:

The device is insensitive to certain colors or materials.

Remedy:

Cause:

The cover of the surface detection sensor is dirty, and a wrong signal is detected, activating the UV light.

Remedy:

Cause:

Overheat protection activated.

Remedy:

1. Clear any blockages in the air vent.

2. Clean or replace the foam filter and motor protection filter

3. Wait 30 minutes until the machine is cooled down.